Agilent Technologies 5977B CI MSD Operating Manual Download Page 74 | Manualshive

Page: 74 / 254

background image

3

Installing Intuvo 9000 GC Columns



To Install the GC/MSD Interface Tip Seal

74

5977B Series MSD Operating Manual

To Install the GC/MSD Interface Tip Seal

Materials needed

•

Interface tip seal (G3870-20542)

•

Tip seal spring (G7005-20024)

•

Knurled tip seal retainer (G3870-20547)

The interface tip seal must be in place for the CI source, the EI XTR source,
and HES. The interface tip seal, spring, and knurled tip seal retainer are not
used with EI SS or Inert source.

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

Procedure

1

Verify that the CI source, EI XTR source, or HES is installed. The tip seal,
spring, and knurled tip seal retainer must not be installed when an EI SS or
Inert source is installed. (See

2

Remove the interface tip seal, spring, and knurled nut retainer from the ion
source storage box. In this order, slide the spring, tip seal, and knurled tip seal
retainer over the column sleeve.

CAUTION

Electrostatic discharges to analyzer components are conducted to the side
board where they can damage sensitive components. Wear a grounded
antistatic wrist strap, and take other antistatic precautions

before

you open

the analyzer chamber.

CAUTION

Always wear clean gloves while handling any parts that go inside the GC or the
analyzer chambers.

«
...
72
73
74
75
76
...
»

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Brand: Camplux Pages: 44

Brand: Panasonic Pages: 224

Brand: Eaton Pages: 20

Brand: Eaton Pages: 21

Brand: Garantia Pages: 2

Brand: Quooker Pages: 12

Brand: PAPILLON Pages: 22

Brand: ProMinent Pages: 20

Brand: vacuubrand Pages: 80

Brand: DAB Pages: 41

Brand: habitat et jardin Pages: 19

Brand: T Therm Geo Pages: 53

Brand: Rheem Pages: 52

Brand: Oasis Pages: 40

Brand: Dräger Pages: 28

Marvair MAA1020H

Brand: ACS Pages: 61

JEFSUBPDW266-95

Brand: Jefferson Pages: 12

Brand: Ozito Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands