manualshive.com logo in svg

Agilent Technologies 5977B CI MSD, Operating Manual

The Agilent Technologies 5977B CI MSD is an advanced scientific instrument offering precise and reliable mass spectrometry analysis. To ensure optimal usage, download the comprehensive Operating Manual for free from our website. This user-friendly manual provides detailed instructions and troubleshooting insights for maximizing the capabilities of the 5977B CI MSD.

Share
Download
background image

2

Installing 8890 GC Columns

The GC/MSD Interface for an 8890 Series GC

52

5977B Series MSD Operating Manual

The GC/MSD Interface for an 8890 Series GC

The GC/MSD interface is a heated conduit into the MSD for the capillary column. 
(See 

Figure 9

.) It is bolted onto the right side of the analyzer chamber, with an 

O-ring seal. It has a protective cover which should be left in place. 

One end of the interface passes through the side of the GC and extends into the 
oven. This end is threaded to allow connection of the column with a nut and 
ferrule. The other end of the interface fits into the ion source. The end of the 
capillary column extends slightly past the end of the column guide tube and into 
the ionization chamber.

Figure 9.

GC/MSD interface for an 8890 GC with EI XTR, HES, and CI sources

Ionization 
chamber

Analyzer 
chamber

Heater/Sensor 
assembly

MSD

GC oven

Heater sleeve

Insulation

Column

Column 
guide tube

Optional entry for CI 
reagent gas or JetClean 
system hydrogen

Tip seal 
assembly

Ion source

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

AquaPRO TSC130 PRO Operating And Parts Manual preview
TSC130 PRO
Brand: AquaPRO Pages: 4
K Tool International KTI63716 Owner'S Manual preview
KTI63716
Brand: K Tool International Pages: 20
Vulcan-Hart 648 135 Owner'S Manual And Installation Instructions preview
648 135
Brand: Vulcan-Hart Pages: 40
Grundfos Sololift+ WC-1 Installation And Operating Instructions Manual preview
Sololift+ WC-1
Brand: Grundfos Pages: 16
Calorex Pro-Pac 30 Technical Manual preview
Pro-Pac 30
Brand: Calorex Pages: 24
Wilden PX4 series Engineering, Operation & Maintenance preview
PX4 series
Brand: Wilden Pages: 43
Saci DRENAG 1000-1200 Instruction For Installation And Maintenance preview
DRENAG 1000-1200
Brand: Saci Pages: 134
GORMAN-RUPP PUMPS Super T T6C60SC-B Installation, Operation And Maintenance Manual preview
Super T T6C60SC-B
Brand: GORMAN-RUPP PUMPS Pages: 38
GE Zoneline AZ91H18E E Series Owner'S Manual preview
Zoneline AZ91H18E E Series
Brand: GE Pages: 78
Carlisle DX200-3SM Service Manual preview
DX200-3SM
Brand: Carlisle Pages: 24
Realax ISI 10 Operating Instructions Manual preview
ISI 10
Brand: Realax Pages: 60
Wilo Actun OPTI-QS Series Installation And Operating Instructions Manual preview
Actun OPTI-QS Series
Brand: Wilo Pages: 364
TCM MMCUT18AS2 Service Manual preview
MMCUT18AS2
Brand: TCM Pages: 127
Samoa 561100 Technical Service Manual And Spare Parts Listing preview
561100
Brand: Samoa Pages: 10
Franklin Electric Little Giant 16 G Series Owner'S Manual preview
Little Giant 16 G Series
Brand: Franklin Electric Pages: 36
KIRLOSKAR KOSN Series Installation, Operation & Maintenance Manual preview
KOSN Series
Brand: KIRLOSKAR Pages: 11
Laars INDIRECT-FIRED Installation And Operating Manual preview
INDIRECT-FIRED
Brand: Laars Pages: 36
DAB E.SYBOX MINI Instruction For Installation And Maintenance preview
E.SYBOX MINI
Brand: DAB Pages: 708

Brands by name

Popular brands

Load more brands