Agilent Technologies 5977B CI MSD Operating Manual Download Page 241

Page: 241 / 254

CI Maintenance



To Clean the CI Source

5977B Series MSD Operating Manual

241

To Clean the CI Source

Materials needed

•

Abrasive paper (5061-5896)

•

Alumina abrasive powder (8660-0791)

•

Aluminum foil, clean

•

Cloths, clean (05980-60051)

•

Cotton swabs (5080-5400)

•

Glass beakers, 500 mL

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Solvents

•

Acetone, reagent grade

•

Methanol, reagent grade

•

Methylene chloride, reagent grade

•

Ultrasonic bath

Preparation

Disassemble the CI source. (See

“To Disassemble the CI Source”

page 238.)

Collect the following parts to be cleaned for a CI source: (See

Figure 79

page 242.)

•

Repeller

•

Source body

•

Drawout plate

•

Drawout cylinder

•

Ion focus lens

•

Entrance lens

These are the parts that contact the sample or ion beam. The other parts
normally should not require cleaning.

Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands