manualshive.com logo in svg

Agilent Technologies 5977B CI MSD, Operating Manual

The Agilent Technologies 5977B CI MSD is an advanced scientific instrument offering precise and reliable mass spectrometry analysis. To ensure optimal usage, download the comprehensive Operating Manual for free from our website. This user-friendly manual provides detailed instructions and troubleshooting insights for maximizing the capabilities of the 5977B CI MSD.

Share
Download
background image

8

CI  Maintenance

To Clean the CI Source

242

5977B Series MSD Operating Manual

.

Procedure

1

If the contamination is serious, such as an oil backflow into the analyzer, 
seriously consider replacing the contaminated parts.

2

Abrasively clean the surfaces that contact the sample or ion beam.

Use an abrasive slurry of alumina powder and reagent-grade methanol on a 
cotton swab. Use enough force to remove all discolorations. Polishing the 
parts is not necessary; small scratches will not harm performance. Also 
abrasively clean the discolorations where electrons from the filaments 
enter the source body.

3

Rinse away all abrasive residue with reagent-grade methanol.

Ensure 

all

 abrasive residue is rinsed 

before

 ultrasonic cleaning. If the 

methanol becomes cloudy or contains visible particles, rinse again three 
times.

4

Separate the parts that were abrasively cleaned from the parts that were not 
abrasively cleaned.

CAUTION

If the CI repeller insulator is dirty, clean it with a cotton swab dampened with 
reagent-grade methanol. If that does not clean the insulator, replace it. Do not 
abrasively or ultrasonically clean the insulator.

Figure 79.

CI source parts to be cleaned

Entrance lens

Ion focus lens Drawout cylinder

Drawout plate

Source body

Repeller

    

             

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Danfoss DHP-A Installation Manual preview
DHP-A
Brand: Danfoss Pages: 64
Danfoss DHP-A Service Instructions Manual preview
DHP-A
Brand: Danfoss Pages: 86
Danfoss DHP-A User Manual preview
DHP-A
Brand: Danfoss Pages: 28
Zip HydroTap G4 Install Instructions Manual preview
HydroTap G4
Brand: Zip Pages: 16
Daikin VRV EMERION RXYQ-AATJA Service Manual preview
VRV EMERION RXYQ-AATJA
Brand: Daikin Pages: 429
A.O. Smith ITE 400 Specifications preview
ITE 400
Brand: A.O. Smith Pages: 4
PAPILLON NARWHAL Instruction Manual preview
NARWHAL
Brand: PAPILLON Pages: 16
SHURflo NG11V Operating Instructions, Performance, Specifications And Parts Manual preview
NG11V
Brand: SHURflo Pages: 16
Milton Roy GB Series Instruction Manual preview
GB Series
Brand: Milton Roy Pages: 43
Sam ZM 375/00 Operation & Maintenance Manual preview
ZM 375/00
Brand: Sam Pages: 23
American Water Heater Powerflex PDVG-40T42 Replacement Parts preview
Powerflex PDVG-40T42
Brand: American Water Heater Pages: 4
Day and Night R4H3 Installation Instructions Manual preview
R4H3
Brand: Day and Night Pages: 18
SAMES KREMLIN REXSON 2B588 User Manual preview
REXSON 2B588
Brand: SAMES KREMLIN Pages: 51
Daikin ETSXB16E Installer'S Reference Manual preview
ETSXB16E
Brand: Daikin Pages: 316
Magic-Pak MHP4-12 Series Installation And Maintenance Instructions Manual preview
MHP4-12 Series
Brand: Magic-Pak Pages: 18
Raypak PROTÉGÉ RPAGP Service Instructions preview
PROTÉGÉ RPAGP
Brand: Raypak Pages: 3
Hoshizaki ROX-30SA-EW Instruction Manual preview
ROX-30SA-EW
Brand: Hoshizaki Pages: 10
OSO S 120 Installation And User Manual preview
S 120
Brand: OSO Pages: 44

Brands by name

Popular brands

Load more brands