Agilent Technologies 5977B CI MSD Operating Manual Download Page 217

Page: 217 / 254

General Maintenance



To Install the EI XTR, SS, or Inert Source

5977B Series MSD Operating Manual

217

To Install the EI XTR, SS, or Inert Source

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Pliers, long-nose (8710-1094)

Procedure

Slide the ion source into the source radiator. (See

Figure 70

Insert and hand tighten the source thumbscrews. Do not overtighten the
thumbscrews. (See

Figure 70

Connect the ion source wires. (See

“To Connect/Disconnect Wiring from the

EI XTR, SS, and Inert Sources”

on page 197.)

Close the analyzer chamber. (See

“To Close the Analyzer Chamber”

page 220.)



Figure 70.

Installing the EI source

Ceramic source board

Ion source

Thumbscrews

Source heater and
temperature sensor wires

Source radiator

Extractor wire



Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands