manualshive.com logo in svg

Agilent Technologies 5977B CI MSD, Operating Manual

The Agilent Technologies 5977B CI MSD is an advanced scientific instrument offering precise and reliable mass spectrometry analysis. To ensure optimal usage, download the comprehensive Operating Manual for free from our website. This user-friendly manual provides detailed instructions and troubleshooting insights for maximizing the capabilities of the 5977B CI MSD.

Share
Download
background image

7

General Maintenance

To Connect/Disconnect Wiring from the EI XTR, SS, and Inert Sources

5977B Series MSD Operating Manual

197

To Connect/Disconnect Wiring from the EI 
XTR, SS, and Inert Sources

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Pliers, long-nose (8710-1094)

•

Tweezers (8710-2460)

Procedure

1

Use tweezers or needle nose pliers to connect/disconnect the ceramic 
source board wire leads at the source connectors. (See 

Figure 63

.)

2

Use tweezers or needle nose pliers to connect/disconnect the source heater 
wire leads at the ceramic source board.

Figure 63   Wiring for the EI XTR Source

Extractor lens

Source heater

Repeller

Filament 1

Source RTD

Filament 2

Ceramic source board

Entrance lens

Ion focus lens

    

             

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Galmet Prima Installation And Operation Manual preview
Prima
Brand: Galmet Pages: 256
dafi IPX4 Operating Instructions Manual preview
IPX4
Brand: dafi Pages: 12
Walrus TPHK Series Installation Manual preview
TPHK Series
Brand: Walrus Pages: 12
Kamar S1904 Use Instruction preview
S1904
Brand: Kamar Pages: 8
WilTec CTF-2800 Operating Instructions Manual preview
CTF-2800
Brand: WilTec Pages: 8
Zoeller Basement Sentry 507 Installation Manual preview
Basement Sentry 507
Brand: Zoeller Pages: 8
Elkay MFWSF100 Mounting Instructions preview
MFWSF100
Brand: Elkay Pages: 2
ACE INSTRUMENTS DPI-2200 Instruction Manual preview
DPI-2200
Brand: ACE INSTRUMENTS Pages: 3
York SINGLE PACKAGE DUAL FUEL HEAT PUMP User Manual preview
SINGLE PACKAGE DUAL FUEL HEAT PUMP
Brand: York Pages: 8
GASLAND chef AS150 Installation Instructions Manual preview
AS150
Brand: GASLAND chef Pages: 60
P.Lindberg 9027885 Manual preview
9027885
Brand: P.Lindberg Pages: 54
Graco 224342 A Series Instructions Manual preview
224342 A Series
Brand: Graco Pages: 28
Pacific hydrostar PACIFIC HYDROSTAR 1/3 HP Submersible Sump Pump with Vertical Float... Manual preview
PACIFIC HYDROSTAR 1/3 HP Submersible Sump Pump with Vertical Float...
Brand: Pacific hydrostar Pages: 9
Waterline Technology AlwaysFresh HFC-1000 Installation And Operation Manual preview
AlwaysFresh HFC-1000
Brand: Waterline Technology Pages: 6
Pentair Hydromatic H3HX Installation And Service Manual preview
Hydromatic H3HX
Brand: Pentair Pages: 8
Biral 25-10 180 Installation And Operating Instructions Manual preview
25-10 180
Brand: Biral Pages: 156
Jefferson JEFSUBPDW266-95 User Manual preview
JEFSUBPDW266-95
Brand: Jefferson Pages: 12
iDM HYGIENIK 2.0 Installation Instruction preview
HYGIENIK 2.0
Brand: iDM Pages: 60

Brands by name

Popular brands

Load more brands