Agilent Technologies 11970 Series User Manual Download Page 53

Page: 53 / 78

Chapter 3

Performance Tests

Performance Test Procedures

orm

nce

est

Table 3-3. Recommended Test Equipment for 11970Q

Instrument

Critical Specifications

Recommended Model

Spectrum Analyzer

LO and IF ranges compatible with mixer

8566B

Synthesized Sweeper

Frequency: 11.0 to 16.7 GHz
Output Level: >0 dBm

8340A

Amplifier

Output Level: >18 dBm leveled
Frequency Range: 4 to 6 GHz

11975A

Amplifier

Frequency Range: 11.0 to 16.7 GHz
Output Level >15 dBm

8349A

Power Meter

Compatible with Power Sensor

436A

Power Sensor

SWR: <2.0

Q8486A

Power Sensor

SWR: <1.3 @ 6 GHz

8485A

Directional Coupler

1. Calibration data for the coupling ration between the output arm and the auxil-

iary arm is necessary for accurate measurements.

Coupling: 20 dB
Directivity: >30 dB
Auxiliary Arm SWR: <1.2

Q752D

Isolator

Insertion Loss: <2 dB
Isolation: >20 dB
SWR: <1.5

Q365A

Frequency Tripler

Conversion Loss: <20 dB

Spacekom Microwave

TKa-1

2. Honeywell, Inc. Spacekom Microwave Center, Santa Barbara, CA

Adapter

SMA female to Type N female

P/N 1250-1404

Adapter

SMA female to SMA female

P/N 1250-1158

Adapter (2 required)

Type N male to SMA female

P/N 1250-1250

Cables (4 required)

Connectors: SMA male

P/N 5061-5458

Cable

Connectors: SMA male
Loss: <1.0 dB @ 20 GHz

P/N 8120-4396

Cable

Connectors: BNC male

11086A

Summary of Contents for 11970 Series















































































Search results

Summary of Contents for 11970 Series

Reviews:

Brands by name

Popular brands

Agilent Technologies 11970 Series, User Manual

Search results

Summary of Contents for 11970 Series

Reviews:

Brands by name

Popular brands