AGI UTX Series Assembly Manual Download Page 22

Page: 22 / 92

31084 R3

4.4. Hydraulic Fittings and Bolt Tightening

Remember the following basic considerations when tightening hydraulic fittings and bolts:

• Tighten all fasteners to the torque specified in . Do not replace or substitute bolts, nuts, or other hardware

that is of lesser quality than the hardware supplied by the manufacturer.

• All hydraulic fittings should be torqued to the recommended specifications. See

Section 6.2 – Fittings Torque

Values on page 89

Do not over-tighten fittings. Over-tightening hose fittings can crack the fittings or motor body
and will void the warranty.

4.5. Brand and Model Decal Placement

Important

Do not cover any existing safety or instruction decals with the model decals.

1. Apply decals to both sides of auger trough.

2. Center decals vertically and apply to auger trough.

24"

MODEL DECAL

52"

BRAND DECAL

4.6. Assemble U-Trough & Flighting

Flight Connector Shaft

Locknut, 7/16"

Bolt, 7/16" x 3"

Bolt, 7/16" x 1-1/4"

4. ASSEMBLY

UTX SERIES – PORTABLE U-TROUGH GRAIN AUGER

Summary of Contents for UTX Series





























































































Search results

Summary of Contents for UTX Series

Reviews:

Related manuals for UTX Series

Brands by name

Popular brands

AGI UTX Series, Assembly Manual

Search results

Summary of Contents for UTX Series

Reviews:

Related manuals for UTX Series

Brands by name

Popular brands