AGFA DRYSTAR AXYS Service Manual Download Page 54

Page: 54 / 461

DD+DIS033.07E

Controls, Connections and Setup Procedure

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Edition 1, Revision 1

DRYSTAR AXYS

Chapter 1 / 18

06-2008 Type

5367/100

Agfa Company Confidential

Printer - Modality connection

The purpose of this section is to show the tasks that are required for connection of the
printer to the modality.

The following table lists these tasks.

Task

Importance

Accessible via * ...

Details see...

Let the modality be
set-up

mandatory

X5.1

5.1

Set-up logical printers

optional

Browser pages

X5.2

5.2

Print diagnostic and/or
test images

mandatory

X5.3

5.3

Adjust image settings

optional

Key-operator menu and

Browser pages

X5.4

5.4

5.1

Modality set-up

(1)

Let the modality be set-up at the modality.

(2)

Tell the modality service engineer following printer parameters:

•

Printer Type (Agfa DRYSTAR AXYS)

•

address

•

AE-title

•

Available film formats.

Summary of Contents for DRYSTAR AXYS














































































































































































































































































































































































































































































Search results

Summary of Contents for DRYSTAR AXYS

Reviews:

Brands by name

Popular brands

AGFA DRYSTAR AXYS, Service Manual

Search results

Summary of Contents for DRYSTAR AXYS

Reviews:

Brands by name

Popular brands