AGFA DRYSTAR AXYS Service Manual Download Page 55

Page: 55 / 461

DD+DIS033.07E

Controls, Connections, and Setup Procedures

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Edition 1, Revision 1

DRYSTAR AXYS

Chapter 1 / 19

06-2008 Type

5367/100

Agfa Company Confidential

5.2

Logical printers Set-up

(1) Check, whether the printer requires the "logical printer setup", i.e. to setup more

than one AE title for the printer. See flowchart below:

Okay. Logical

Printer Setup not

required.

Okay. Logical Printer

Setup not required.

Perform adjustments

at modality.

Create two logical printers.

Proceeding see this section.

Yes

536401mm.cdr

Yes

Adjustment

at modality

possible?

Logical Printer

Setup Decision

Flowchart

Check whether modality supports

more than one application (e.g. Mammo + CR).

Check whether images of

different applications can

be adapted to required settings.

Example. DR: Dmax 3.2; LUT: Kanamori

Mammo: Dmax: 3.8, LUT: linear

Modality supports

> 1 application ?

Figure 12

Summary of Contents for DRYSTAR AXYS














































































































































































































































































































































































































































































Search results

Summary of Contents for DRYSTAR AXYS

Reviews:

Brands by name

Popular brands

AGFA DRYSTAR AXYS, Service Manual

Search results

Summary of Contents for DRYSTAR AXYS

Reviews:

Brands by name

Popular brands