manualshive.com logo in svg

AGFA DRYSTAR AXYS, Service Manual

Share
Download
AGFA DRYSTAR AXYS Service Manual Download Page 161

 
 
DD+DIS033.07E 

Repair and Service

Tools and Auxiliary Means

 
 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled. 

4 

Software Installation 

 

You want to ... 

Example 

Refer to ..... 

Upgrade the SW to a higher 
basic release 

SW Upgrade from SW Rel. 
1.80_C1 to 2.0.0_C1 

Installation Instructions 

which are part of the 

software 

Update the SW with a patch  SW Update from 1.8.0_C1 to 

1.8.1_C1 

4.1

 

Install SW on a new, empty 
hard drive or. 

Install SW 1.8.0_C1 on an 
empty hard drive 

4.2

 

Re-install the software on a 
printer in ERROR - SYSTEM 
FAILURE state. 

Re-Install SW 1.8.0_C1 on a 
printer that does not bootup 
anymore. 

4.3

 

 

 

 

NOTE: 

•

 

A software upgrade is a functional extension. It is usually sold through the Sales 
and Services Channels 

•

 

A software update is a corrective modification of the basic software version. It 
does not include new functionality. SW Updates (Patches) are available on 
MedNet. 

 

4.1 

SW Update: Loading a SW Patch 

This chapter describes the SW Update with a patch. 

 

 

NOTE: 

For instructions regarding SW upgrade to a higher basic release (e.g. SW Upgrade 
from SW Rel. 1.80_C1 to 2.0.0_C1) refer to Chapter 7, Modifications 

 

A SW Update can be performed in two ways: 

SW Update via ... 

Refer to ..... 

Key-operator menu at the local keypad using the CF card 

4.1.1

 

Service menu in the Printer browser pages using the 
network connection  

4.1.2

 

 

Edition 1, Revision 0 

DRYSTAR AXYS 

Chapter 3.2 / 55 

10-2007 Type 

5367/100 

Agfa Company Confidential

 

Summary of Contents for DRYSTAR AXYS














































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands