manualshive.com logo in svg

AGFA CR, User Manual, Page: 3 / 32

Share
Download
AGFA CR User Manual Download Page 3

3

2313B EN 20041109

CR U

SER

S

TATION

Table of contents

Chapter 1: 

Introducing the CR User Station

.................................................... 5

Components of the CR User Station

................................................................ 6

Positioning of the CR User Station

.................................................................. 7

Possible configurations

.................................................................................... 8

Dedicated configuration

............................................................................... 9

Interchangeable configuration

.................................................................... 10

Configuration with Direct ID

....................................................................... 11

Safety precautions

......................................................................................... 12

General safety instructions

......................................................................... 12

Safety precautions for the monitor

.............................................................. 13

Safety instructions for cleaning the CR User Station

................................... 13

Safety compliance

......................................................................................... 14

Equipment for the CR Operator Console

....................................................... 15

Switching ON the ID Tablet

............................................................................ 17

ID Software

.................................................................................................... 18

Inserting cassettes

......................................................................................... 19

Appendix A: 

Technical specifications

............................................................ 21

Technical Specifications (for the CR User Station and included equipment)

.. 22

Technical Specifications (for the other equipment*)

....................................... 24

Appendix B: 

Remarks for HF-emission and immunity

.................................. 25

Remarks for HF-emission and immunity

........................................................ 26

Summary of Contents for CR

































Reviews:

No comments