background image

3

Clean Before Using

After you remove all of the packaging materials, clean the inside of 

your refrigerator before using it. See the cleaning instructions in 

“Refrigerator Care.”

Location Requirements

To ensure proper ventilation for your refrigerator, allow for 

¹⁄2

(1.25 cm) of space on each side and at the top. Allow for 1" 

(2.54 cm) of space behind the refrigerator. If your refrigerator has 

an ice maker, allow extra space 

at the back for the water line 

connections. When installing your refrigerator next to a fixed wall, 

leave 2

¹⁄2

" (6.3 cm) minimum on the hinge side (some models 

require more) to allow for the door to swing open.

NOTE:  This refrigerator is intended for use in a location where the 

temperature ranges from a minimum of 55°F (13°C) to a maximum 

of 110°F (43°C). The preferred room temperature range for 

optimum performance, which reduces electricity usage and 

provides superior cooling, is between 60°F (15°C) and 90°F 

(32°C). It is recommended that yo u do not install the refrigerator 

near a heat source, such as an oven or radiator.

Electrical Requirements

Before you move your refrigerator into its final location, it is 

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz., AC only, 15- or 20-amp fused, grounded 

electrical supply is required. It is recommended that a separate 

circuit serving only your refrigerator be provided. Use an outlet 

that cannot be turned off by a switch. Do not use an 

extension cord.
NOTE:  Before performing any type of installation, cleaning, or 

removing a light bulb, turn the control (Thermostat, Refrigerator or 

Freezer Control depending on the model) to OFF and then 

disconnect the refrigerator from  the electrical source. When you 

are finished, reconnect the refriger ator to the electrical source and 

reset the control (Thermostat, Re frigerator or Freezer Control 

depending on the model) to the desired setting. See “Using the 

Controls.”

Important information to know about glass shelves 

and covers:

Do not clean glass shelves or covers with warm water when 
they are cold. Shelves and covers may break if exposed to 
sudden temperature changes or impact, such as bumping. 
Tempered glass is designed to shatter into many small, 
pebble-size pieces. This is normal. Glass shelves and covers 
are heavy. Use both hands when removing them to avoid 
dropping.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as 

gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.

2

¹⁄2

" (6.3 cm)

¹⁄2

" (1.25 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, 

fire, or electrical shock.

WARNING

See “dimensions” on page 4.

Summary of Contents for AMLFDR20

































Reviews: