background image

 

 

28 

5.7.  ACRE METER OPTION 

The option electronic hubodometer threads into a ½” 
fine hole tapped into the end of the right hand center 
roller shaft. Install the acremeter with a oil filter wrench 
to 23 lb foot of torque with a lock washer to ensure that 
the unit is not lost. t is protected by a flange welded 
onto the The Veeder Root electronic acre meter.  
 

 

FIGURE 25 ACREMETER TO PROGRAM 
MODE 

 

See Figure 25 ACREMETER TO PROGRAM 
MODE 
above.  

 
The acre meter calibration is done by touching  a 
magnet to the outside of the face of the odometer on a 
Left spot  marked “A” and Right spot marked “B” The 
simplified instructions to set to 88.0 for a 45  foot 
LandRoller are:  

1)  Hold magnet on the left position- 

“A” – in 6 

seconds will read serial number,  leave on 
MUCH longer 

– until PROG shows on screen.  

  

2)  Lift off of left calibration for 1 second, touch 

magnet down to see units= “acres” set already 

3)  Lift and touch left again advance to revolutions 

per acre,     0000.0 acres per revolution will 
show

—should be   0088.0 for a 45 foot –  

 

FIGURE 26 CALIBRATING "REVS" FOR 45 

 

4)  Touch left to advance to second left zero-  
5)  Touch left again to have the third left digit of 

0000.0 flashing,  

6) 

Touch right “B”  eight times  to have the 0 
advance to first “8” of  0088.0 

7)  Touch left to advance to fourth left digit of 

0000.0. 

8) 

Touch right “B” 8 times  to advance to “8” in 
the fourth digit.  

9)  Do nothing for 10-20 seconds, and front 

screen will come up reading 88.0 revs acres in 
lower left. DO NOT continue to more 
programming as the counter may become 
locked and of no value.   

Consult the tabled below for other calibration numbers. 
 

 

machine  width 
feet 

17.0 

20.0 

 

31.0  

40.0 

45.0 

 

46.0 

52.0 

62.0 

66.0 

70.0 

80.0 

machine width 
meters 

5.2 

6.1 

 

9.5 

12.2 

13.7 

 

14.0 

15.9 

18.9 

20.1 

21.3 

24.4 

acres per 1/2 mile 

1.0 

1.2 

1.86 

2.4 

2.7 

2.76 

3.2 

3.8 

4.0 

4.2 

4.8 

rev per one acre 

233.0  198.1  127.8 

99.0 

88.0 

86.1 

76.2 

63.9 

60.0 

56.6 

49.5 

  

  

  

 

  

  

 

  

  

  

  

  

rev per 1 hectare 

575.8  489.5  3.161  244.7  217.5 

213.  188.3  157.9  148.3  139.8  122.4 

acres / hour @5 
mph 

10.3 

12.1 

 

18.76 

24.2 

27.3 

 

27.9 

31.5 

37.6 

40.0 

42.4 

48.5 

 

Summary of Contents for LandRoller
























































Reviews: