background image

OptRx

PN 2006020–ENG Rev. H

2.

Enter Reference Strip Information

The Reference Strip Information screen 
appears.

Select the correct 

Sensor Rx

. Press 

 to enter the Name, Growth Stage, 

and Variety. For Europe Algorithm Settings 
view below.

÷

NOTE! For Corn, a growth stage of V5 or 
later is needed for accurate application.

When selecting Europe as Sensor Rx, the 

Europe Algorithm Settings

 become 

active. A region, a crop type and a Growth 
Stage need to be selected. 

If your region is not noted in the drop-
down menu, select the 

Region

 that 

reflects your current position best when 
comparing geographic location, climate, general soil types and farming practices. The region setting is used for fine-
tuning and optimizing the N Algorithm. 

Select the 

Crop Type

 on which you are applying fertilizer. For the crops Wheat, Barley and Rapeseed the N Algorithm 

is verified by independent field experiments.

Select the 

Growth Stage

 that reflects your current crop status. For Wheat and Barley the Growth Stage is used to 

select the most appropriate VI index, NDVI or NDRE, further it will be used for fine-tuning and optimizing the N-
Algorithm.

Press 

 when finished.

3.

Drive Reference Strip

—A screen appears, stating that you should drive the applicator to the start of the reference 

strip. When ready, press 

 and drive the reference strip.

4.

Recording Reference Strip

—When you are driving the Reference Strip, 

 appears in the 

Equipment Tab. This bar counts the number of seconds that you record the reference strip.

For best results when driving the Reference Strip, it may be beneficial to Pause the Reference Strip when driving over 
parts of the field that are in a lower than average condition, such as the headlands.

After the minimum required time elapses to create a Reference Strip, the “Cancel” button will change into 

.

5.

File Name

—Press the Stop button when you wish to finish creating the Reference Strip. A dialog appears indicating 

the Reference Strip is saved. Press 

 to accept.

Reference Strip Information

Sensor 

Rx:

Name:

Growth 

Stage:

Variety:

Corn

Europe Algorithm Settings

Region: UK

Crop 

Type: Wheat

Growth 

Stage: GS21 (Tillering)

Recording 303

Stop

Summary of Contents for OptRx















Reviews: