AFi MR-913D Instruction Manual Download Page 8

 

8

SYNC 

A bi-color LED indicator is provided to monitor the proper serialization of the optical data stream into 
the MR-913D electronic interface. DC power and sync status associated with this LED is summarized 
below. 
 

Sync LED 

DC Power Status 

Sync Status 

Green 

On  

Proper Data Stream Serialization Present 

Red 

On 

Data Stream Serialization Not Detected 

Off 

Off 

Check Power Supply 

 
 
 
 
 
 
 
 

 

 
 
 

 
 
 
 

 
LIFETIME WARRANTY INFORMATION 

American Fibertek, Inc warrants that at the time of delivery the products delivered will be free of defects 
in materials and workmanship. Defective products will be repaired or replaced at the exclusive option of 
American Fibertek. A Return Material Authorization (RMA) number is required to send the products 
back in case of return. All returns must be shipped prepaid. This warranty is void if the products have 
been tampered with. This warranty shall be construed in accordance with New Jersey law and the 
courts of New Jersey shall have exclusive jurisdiction over this contract. 

EXCEPT FOR THE 

FOREGOING WARRANTY, THERE IS NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR 
A PARTICULAR PURPOSE OR OTHERWISE, EXPRESSED OR IMPLIED, WHICH EXTENDS 
BEYOND THE WARRANTY SET FORTH IN THIS AGREEMENT.

 In any event, American Fibertek will 

not be responsible or liable for contingent, consequential, or incidental damages. No agreement or 
understanding, expressed or implied, except as set forth in this warranty, will be binding upon American 
Fibertek unless in writing, signed by a duly authorized officer of American Fibertek. 

 

  

SERVICE INFORMATION 

There are no user serviceable parts inside the unit. 
In the event that service is required to this unit, please direct all inquiries to: 
 
American Fibertek, Inc. 

Phone: (877) 234-7200 

120 Belmont Drive 

Phone: (732) 302-0660 

Somerset, NJ  08873 

FAX (732) 302-0667 

E-mail: 

[email protected]

 

Summary of Contents for MR-913D









Reviews: