AFFA AFPD-022 Operating Instructions Manual Download Page 7

Page: 7 / 8

Program Operation

1.Entering into interface

4.Specification setting

2.Operation Interface

3.Operation switch

When you connected the power and open the air-break switch, you will enter into a blinking LED
interface (digital tube will check all lightly or full-body). If your password is "000" (default
password), then flashes three times later, it will enter into the operation interface. Or you have to
press Up Button and Down Button to enter into the Operation Interface through the password one
by one.

Using the UP Button and DOWN Button can check and edit the parameter. When there is any
parameter that need to be changed , please press the edit buttons, and then you will see the
delaying time in the relative channel . after editing the parameter , press the edit buttons . and
then it will come back to the first interface, which showing OFF or ON

A.Stand-alone

No operation button, but showing “OFF”, it means output has been closed
No operation button, but showing “ON”, it means output has been opened.
When reading “OFF” on Switch, it means the output will be closed timely
When reading “ON” on Switch, it means the output will be opened timely
(“1**”) what is it closed or opened is the No2 channel(*2*), delay3x0.5s (*3*).
Parameter setting interface and changing the password, please refer to the relevant programming
interface operation

B.Line interface

No operation button, but showing “OPN”, it means output has been closed
No operation button, but showing “CLS”, it means output has been opened.
Sequential machine and Stand-alone interfaceNo parameters setting or password changing
when being carried out

In the condition that the one-way switch has not closed , enter into the user interface, you only
need to continue pressing the switch button for one second, you can switch to sequential machine
(less than 1S, operation invalid)

A.Powered on punctually

When entering into the operation interface and all the ways have been closed. Please press the
mother switch for 1 second , then it will be powered on on time . (showing ON)
When the system is closed now, please press the switch for 1 second, it will be opened on time.

B.Powered off punctually

When all the ways are opened , please keep pressing the mother switch for 1 second , and then

you could power off the system punctually . (showing OFF)

When the system is opened now, please press the switch for 1 second, it will be closed on time.

1.Input socket

2.Main Power Switch

3.Voltage Display

4.Programming Interface

5.USB Lampholders

6.Output Indicator

7.One-way switch

Use the 5-pin three-phase industrial power input socket. In accordance with industry standards
(the instructions on the cover is standard) , please insert three-phase lines L1, L2, L3, a zero line
N and a ground line G. Input connectors , L1/N/G, is responsible for the output of the 1-4 in the
rear board ; L2/N/G is responsible for 5-6 ;L3/N/G is responsible for 7-8.

The default connection is the three-phase line L1, L2, L3 plus a zero-line N and a ground wire G of
all connected, so that all output sockets can be used. Please Note that the phase line L1, zero-line
N and ground G have been set to work to take power by factory.
It will be very dangerous , if wiring wrong. please make sure them mark-seated. After plugging the
power firmly, please make sure the power connector correctly to remove any incipient fault for this
and the follow-up equipment.

Three-phase air switch with overcurrent protection and short circuit protection
Normally speaking , any phase current can not exceed 32A for AFPD-022 .Otherwise, it will be
protected automatically .

Through the triple-digit on the LED , it will display the AC voltage of what this device connecting .

Using a LED screen, and three LED lamps to make it display more intuitively .

AFPD-022 comes with a USB lampholder. Power on and insert the USB lamp , it will light . and
then facilitate the operation under weak light .

Using Φ5 bright green lamp, each lamp corresponds to each way of output .

You can turn off a particular output. However, before booting, make sure that all one-way switches
have been switched on, so as to reduce the trouble when re-opening, but also to do an emergency
switch

L1-N: AC220V, 50HZ/60HZ 32A

L2-N :AC220V, 50HZ/60HZ 32A

L3-N :AC220V, 50HZ/60HZ 32A