background image

Page 12

Warranty

Page 12

ONE YEAR WARRANTY

aFe POWER warrants the included hardware product and accessories against defects in 

materials and workmanship for one year from the date of original retail purchase. This 

warranty applies only to the original purchaser of the product and is non-transferrable. 

Proof of purchase of the aFe POWER product is required for all warranty claims. Warranty 

is valid provided aFe POWER instructions for installation and/or cleaning were properly 

followed. Proper maintenance with regular inspections of product is required to insure 

warranty coverage. Damage due to improper installation, failure to provide proper care 

and maintenance, accident, abuse, misuse, normal wear and tear, unauthorized repair or 

alteration is not warranted.

Additionally, Incidental or consequential damages or cost, including installation and 

removal of part, incurred due to failure of aFe POWER product is not covered under this 

warranty. All warranty is limited to the repair and/or replacement of the aFe POWER 

product. Incidental or consequential damage means any loss, expense, or other damage 

that cannot be remedied by either repairing any defect in the aFe POWER product or by 

replacing the aFe POWER product. Some states do not allow the exclusion or limitation of 

incidental or consequential damages, so the above limitations or exclusions may not 

apply to you.  Furthermore, no individual or entity other than aFe POWER possesses the 

authority to alter the obligations, limitations, disclaimers, or exclusions under this 

warranty.  

To request Return Goods Authorization (“RGA”), contact aFe POWER by completing and 

submitting the online technical support form at 

https://afepower.com/contact/tech-

warranty

or call +1(951)493-7100.  Upon receipt of the RGA, you must return the product 

to the address provided in the RGA, freight prepaid and accompanied with a dated proof 

of purchase and the RGA. Upon receipt of the defective product and upon verification of 

proof of purchase, aFe POWER will either repair or replace the defective product within a 

reasonable time, not to exceed thirty days. aFe POWER has the right to deny any 

warranty believed to be false, altered or purchased through an unauthorized dealer.

Summary of Contents for F-250














Reviews: