Aerpro FP9550BK Installation & User Manual Download Page 2

Page: 2 / 56

Page 2

PLEASE READ BEFORE INSTALLATION

The system you are installing acts as a controller for your factory Heating/Cooling

system.

To ensure correct functionality, please confirm the factory system is functioning

correctly prior to installation.

This controller WILL NOT fix any prior issues with the Heating/Cooling system in the

vehicle.

To confirm the factory system is operational, follow the steps below.

1. Check Fan speed control

2. Check the Vents change correctly

3. Check the system changes temperature correctly

4. Confirm Dual Zone separates temperatures correctly

5. Air conditioner

6. SWC (The steering controls must be working in the vehicle previously to work with

our control harnesses. They will not fix previous underlying problems).

If the system is deemed to be operational, Please continue with your Installation

NOTE: Remove any Cd’s in the from the factory head unit before uninstalling

Installation Information

Product and Install Information

If you would like to find more information on this product or download an up to date

digital copy of this manual, please visit the aerpro.com website and search for your

model or scan the QR code below.

FP9550GK

An installation and setup video

is also available on our site

FP9550BK

Summary of Contents for FP9550BK

























































Search results

Summary of Contents for FP9550BK

Reviews:

Related manuals for FP9550BK

Brands by name

Popular brands

Aerpro FP9550BK, Installation & User Manual

Search results

Summary of Contents for FP9550BK

Reviews:

Related manuals for FP9550BK

Brands by name

Popular brands