Aerotech Ndrive HPe 100 Hardware Manual Download Page 33 | Manualshive

Page: 33 / 114

background image

Installation and Configuration

Ndrive HPe 50/75/100

2.3.1.2. Unpowered Motor and Feedback Phasing

Disconnect the motor from the controller and connect the motor in the test configuration shown in

.

This method will require a two-channel oscilloscope, a 5V power supply, and six resistors (10,000 ohm, 1/4
watt). All measurements should be made with the probe common of each channel of the oscilloscope
connected to a neutral reference test point (TP4, shown in

). Wave forms are shown while moving

the motor in the positive direction.

Figure 2-6:

Motor Phasing Oscilloscope Example

With the designations of the motor and Hall leads of a third party motor determined, the motor can now be
connected to an Aerotech system. Connect motor lead A to motor connector A, motor lead B to motor
connector B, and motor lead C to motor connector C. Hall leads should also be connected to their respective
feedback connector pins (Hall A lead to the Hall A feedback pin, Hall B to Hall B, and Hall C to Hall C). The
motor is correctly phased when the Hall states align with the Back EMF as shown in (

). Use the

CommutationOffset parameter to correct for Hall signal misalignment.

Figure 2-7:

Brushless Motor Phasing Goal

www.aerotech.com

Chapter 2

33

«
...
31
32
33
34
35
...
»

Summary of Contents for Ndrive HPe 100



















































































































Reviews:

No comments

Related manuals for Ndrive HPe 100

VLT AutomationDrive FC 302

Brand: Danfoss Pages: 346

Brand: Aerotech Pages: 120

Brand: AOpen Pages: 62

Brand: YASKAWA Pages: 41

Brand: Sealey Pages: 6

Brand: SOMFY Pages: 2

Dexxo Compact RTS

Brand: SOMFY Pages: 10

Brand: SOMFY Pages: 78

Brand: Targus Pages: 14

iPOS8015 BZ-CAT

Brand: Technosoft Pages: 34

Brand: Kanguru Pages: 13

Brand: Grundig Pages: 20

Brand: Binks Pages: 8

CIMR-AC4A0103TAA

Brand: YASKAWA Pages: 40

Brand: IBM Pages: 60

VLT Midi Drive FC 280

Brand: Danfoss Pages: 68

VLT 2800 Series

Brand: Danfoss Pages: 103

Brand: Acclaim Lighting Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands