background image

Overview

MPS50SV Hardware Manual

1.1. Environmental Specifications

W A R N I N G :  Do not expose this product to environments or conditions outside of the listed
specifications. Exceeding environmental or operating specifications can cause damage to the
equipment.

Table 1-2:

Environmental Specifications

Ambient
Temperature

Operating:
The optimal operating temperature is 20° C ±2° C (68° F ±4° F). If at any time the
operating temperature deviates from 20° C, degradation in performance could occur.

Storage: 0° to 40° C (32° to 104° F) in original shipping packaging

Humidity

Operating: 20% to 60% RH

Storage: 10% to 70% RH, non-condensing in original packaging. The stage should be
packaged with desiccant if it is to be stored for an extended time.

Altitude

Operating: 0 m to 2,000 m (0 ft to 6,562 ft) above sea level
Contact Aerotech if your specific application involves use above 2,000 m or below sea
level.

Vibration

Use the system in a low vibration environment. Excessive floor or acoustical vibration
can affect system performance. Contact Aerotech for information regarding your spe-
cific application.

Protection
Rating

The MPS50SV is not suited for dusty or wet environments. This equates to an ingress
protection rating of IP00.

Use

Indoor use only

12

Chapter 1

www.aerotech.com

Summary of Contents for MPS50SV











































Reviews: