background image

Air Coil Nailer       

                        Http://www.aeroprotools.com   

 

parts  of  the  fastener  driving  tool  are  not  in  the  starting  position  following  maintenance  and  repair  work  or 

transportation. 

Connect  the  fastener  driving  tool  to  the  compressed  air  supply  using  suitable  pressure  hose  equipped  with 

quick-action connectors. 

Check  for  proper  functioning  by  applying  the  muzzle  of  the  fastener  driving  tool  to  a  piece  of  wood  or  wooden 

material and actuating the trigger once or twice. 

4.3Filling the magazine 

Only those fasteners specified under TECHNICAL DATA (see 1.1) may be used 

When filling the magazine, hold the tool so that the muzzle is not pointing towards the operator or any other person 

or animals. 

4.4 Handling the tool 

Pay attention to 

2-Special Reference-

of these operating instructions. 

Having checked that the fastener driving tool is functioning correctly, apply the tool to a work piece and actuate the 

trigger. 

Check whether the fastener has been driven into the work piece in accordance with the requirements. 

-  if  the fastener  is  protruding, increase  the  air  pressure  in increments of  0.5  bar,  checking  the  result after 

each new adjustment; 

- if the fastener is driven into an excessive depth reduce the air pressure I increments of 0.5 bar until the 

result is satisfactory. 

You should endeavor in any event to work with the lowest possible air pressure. This will give you three significant 

advantages; 

          1.energy will be saved, 

          2.less noise will be produced, 

          3.a reduction in fastener driving tool wear will be achieved. 

Avoid triggering the fastener driving tool if the magazine is empty. 

Any  defective  or  improperly  functioning  fastener  driving  tool  must  immediately  be  disconnected  from  the 

compressed air supply and passed to a specialist for inspection. 

In the event of longer breaks in work or at the end of the working shift, disconnect the tool from the compressed air 

supply and it is recommended to empty the magazine. 

The  compressed  air  connectors  of  the  fastener  driving  tool  and  the  hoses  should  be  protected  against 

contamination, the ingress of coarse dust chips, sand etc, will result in leaks and damage to the fastener driving 

tool and the couplings. 

5. Maintenance 

Disconnect the tool from the compressor before adjusting, clearing jams, servicing &maintenance, relocating and 

during non operation.   

      Regular lubrication, if your tool without using the in-liner automatic oilier, place 2 or 6 drops of pneumatic tool oil 

into  the  air  inlet  before  each  work  day  or  after  2  hours  of  continuous  use  depending  in  the  characteristic  of 

workpiece or type of fasteners.   

      Air-operated tools must be inspected periodically, and worn or broken parts must be replaced to keep the tool 

operating safely and efficiently. Check and change all worn or damaged O-ring, Seals, etc. Tighten all the screws 

and caps to avoid personal injury. This should be done by an expert. 

      Make regular inspection for free movement of trigger, Spring and safety mechanism to assure safe system is 

complete and functional: no loose and missing parts, no building or stocking parts. 

      Keep magazine and nose of tool clean and free of any dirt lint or abrasive particles. 

      When temperatures are below freezing, tools should be kept warm by any convenient, safe method.   

 

                                                                                                                                                                                                                                                 

Summary of Contents for MCN55









Reviews: