AEROPRAKT 484 Pilot Operating Handbook Download Page 51

51

 

 

 

AEROPRAKT-22L2 Pilot Operating  Handbook                                                  A22L2-POH-02

 

 

 

10.7.4 Balked  landing

 

 

Balked  landing   (go  around)   situation  occurs  due  to  errors  made  during  approach   which 

can  not  be  corrected   or  in  case  if  an  obstacle  is  suddenly  detected  on  the  runway

.  

The 

balked  landing  procedure  is described  in the section 7

.

12

.

 

 

Total  time of balked  landing  training- 20 minutes.  Number  of flights- 1

Number  of 

landings  - 1.

 

 

10.7.5 Low  speed  flight,  recognizing  the starting  and ongoing  stall and stall  recovery

 

 

The  aircraft  has  no  adverse  handling  features  at  low  speeds  and  at  stall  with  any  of  flaps 
settings.  A  light  vibration  of  controls  in roll  may  be  noticed  that  warns  about  approaching  to 
the  stalling   speed.   The  stall  occurs  in  form  of  airplane  pitch  angle  decrease   without  a 
noticeable  change  in  bank  angle.  The  airplane  recovers  from  stall  immediately  if  the  flight 
controls  are  returned  to  their  neutral  position.  During  a  low  speed  flight  with  wings  level 
deflection  of  ailerons  does  not  initiate  stall.  However  during  a  turn  at  a  low  speed  abrupt 
aileron  deflection  may  cause  stall with noticeable  increase  in bank  angle.

 

 

Stall  recovery  procedure  is described  in the section 6.7

.

 

 

Total  time of balked  landing  training- 20 minutes

Number  of flights- 1

Number  of 

landings-  1.

 

 

10.7.6 High speed  flight,  recognizing  and recovery  from steep  diving  spiral

 

 

The  aircraft  has  no  peculiar  handling  features  at  high  speeds.  The  control  forces  increase 
with  airspeed  growing  and  that  impedes  the  abrupt  control  inputs  and  exceeding  the  limit 
loads  due  to  that.  During  high  speed  flight  the  engine  parameters  must  be  monitored  and 
exceeding  its operational  limits must  be prevented.

 

 

To  recover  from  a steep  spiral  the engine  RPM  must  be  reduced  first  and  then  the  airplane 

must  be brought  to level flight by deflecting  gently the ailerons  and elevator.

 

 

Total time  of balked  landing  training 

20 minutes.  Number of flights- 1. Number  of 

landings 

1.

 

 

10.7.7  Short  field  takeoff  and landing  with  overflying  obstacles

 

 

Short  field  takeoff  and  landing  procedures  are  described  in  the  sections  7.11  and  7.12.  To 
fly  over  the  obstacles  (if  any)  during  the  climb  and approach  it  is  recommended  to  set  the

 

flaps  to 2nd position  and fly at the best climb  angle  speed  Vx 

90 km/h  (49 kts)

.

 

 

Total  time of balked  landing  training- 20 minutes

Number  of flights- 1

Number  of 

landings 

4.

 

 

10.7.8 Crosswind  takeoff  and landing

 

 

It is recommended to use 1st  flap setting during  crosswind  takeoff  or landing.

 

 

In  case  of crosswind  takeoff  it is necessary  to rotate  the  yoke by  1/3  of its full travel  against 

the  wind  direction  and  control  the  heading  using  the  rudder  pedals

.  

Then  the  takeoff  will 

occur  with  some  bank  angle.  After  the  takeoff  the  wings  shall  be  set  level,  the  downwind 
drift   shall   be   countered   with   an   appropriate   change   of   heading   and   climb   shall   be 
continued.

 

 

In  case  of  crosswind   landing   it  is  recommended   to  keep  the  airplane   aligned   with  the 

runway  using  rudder  pedals  while  countering  the  downwind  drift  with  a  bank  angle  against 
the  wind  direction

.  

The  bank  angle  value  shall  be  appropriate  to  the  crosswind  strength. 

The bank  shall  be maintained  until touchdown  which will occur  with  one of the main  wheels

 

Summary of Contents for 484






















































Reviews: