background image

Taiwan MPE Warning

電磁波曝露量

MPE

標準值

(MPE) 1mW/cm2

,送測產品實值為

0.734 mW/cm2

Safety Guidelines

The information in this section applies to AP245X devices.

The following safety icons are used in these guidelines to identify the type of precaution:

This icon indicates a general caution. Failure to comply with a caution 
notification can result in damage to equipment.

This icon indicates an electrical caution. Failure to comply with an electrical 

notification can result in serious injury or death, and extensive damage to 

equipment.

The following table lists the safety precautions you should follow when installing your 

AP245X.

Aerohive devices must be installed by a professional installer who is certified to 

install these types of devices and to ensure that they are properly grounded 
and meet applicable local and national electrical codes.

These devices are intended for indoor use only.

Do not install the device in an environment where the operating ambient 

temperature might exceed the recommended ranges.

Electrical equipment generates heat. Ambient air temperature may not be 
adequate to cool equipment to acceptable operating temperatures without 

adequate circulation. Be sure that the room where you install your device has 

adequate air circulation.

Changes or modifications made to this device that are not expressly approved 
by the party responsible for compliance could void the user's authority to 

operate the equipment.

Electrostatic discharge (ESD) can damage equipment and impair electrical 

circuitry. ESD damage occurs when electronic components are improperly 
handled and can result in complete or intermittent failures. Be sure to follow 

ESD-prevention procedures when handling electronic equipment and 

components. 

Never assume that power is disconnected from a circuit; always check the 
circuit.

To meet radiation exposure requirements in all countries, these devices should 

be installed at a minimum distance of 12.6" (32 cm) from people. See individual 

country warning for country-specific distances, if required.

Page 6 of 17

AP245X Hardware User Guide

6/14/2016

Summary of Contents for AP245X


















Reviews: