background image

GUIDE#: pwb-ASSAULT-004

4

PaRts list

ITEM #

DESCRIPTION

QTY

COMMENTS

1

2.25" TOWER JOINT - THREADED (INCL. M6 X 12mm BOLT)

4

2

2.25" TOWER JOINT - THRU HOLE (INCL. M6 X 12mm BOLT)

4

3

DECK MOUNT

4

4

M12 X 40mm BOLT

12

FOR USE WITH ITEMS - 1, 2, 15

5

M12 X 45mm BOLT

8

FOR USE WITH ITEMS - 3, 30

6

M12 X & 75mm BOLT

4

FOR USE WITH ITEMS - 3

7

M12 SPRING LOCK WASHER

24

FOR USE WITH ITEMS - 4, 5, 6

8

M10 X 75mm BUTTON HEAD BOLT

4

FOR USE WITH ITEMS - 27

9

M10 NYLON LOCK NUT

4

FOR USE WITH ITEMS - 8

10

M12 NYLON LOCK NUT

4

FOR USE WITH ITEMS - 6

11

M12 FLAT WASHER

4

FOR USE WITH ITEMS - 6

12

LARGE FLAT WASHER (OD = 70mm)

4

FOR USE WITH ITEMS - 3

13

CURVED RUBBER WASHER (OD = 70mm)

4

FOR USE WITH ITEMS - 3

14

BIG FLAT WASHER (OD = 70mm)

4

FOR USE WITH ITEMS - 3

15

FRONT HINGE (TWO PARTS CONNECTED BY M12 X 40mm BOLT)

2

16

2.5" CLAMP

2

17

2.25" RUBBER COLLAR

2

FOR USE WITH ITEMS - 16

18

2.375" RUBBER COLLAR

2

FOR USE WITH ITEMS - 16

19

CLAMP JOINT WITH SLANT (INCL. M6 X 12mm BOLT)

2

20

M10 X 25mm BOLT

2

FOR USE WITH ITEMS - 19

21

LARGE WASHER FOR SIDE BLADE

4

FOR USE WITH ITEMS - 30

22

M12 ALLEN KEY

1

23

M10 ALLEN KEY

1

24

M8 ALLEN KEY

1

25

M6 ALLEN KEY

1

26

THREADLOCKER

1

27

TOP SECTION TUBE

1

28

LOWER SIDE RAILS

2

29

FRONT LEGS

2

1 PORT & 1 STARBOARD

30

SIDE BLADES

2

ITEM #

DESCRIPTION

QTY

COMMENTS

1

FORKS

2

2

LOGO PLATE WITH BUNGEE CORD

1

3

M6 X 20mm BOLT

4

FOR USE WITH ITEMS - 1, 2

4

M8 X 16mm BOLT

4

USED TO ATTACH RACK ASSEMBLY TO TOWER

TOWER PACKAGE

BOARD RACK PACKAGE

 - PER PACKAGE - 2 PACKAGES ARE GENERALY INSTALLED PER TOWER.

Summary of Contents for Assault Wakeboard Tower














Reviews: