background image

31/07/2019

Door / Window 7 user guide : Aeotec Group

https://aeotec.freshdesk.com/support/solutions/articles/6000218764-door-windows-sensor-7-user-guide

2/10

Importantsafetyinformation.

Please read this and other device guides carefully. Failure to follow the recommendations set forth by Aeotec Limited
may be dangerous or cause a violation of the law. The manufacturer, importer, distributor, and/or reseller will not be
held responsible for any loss or damage resulting from not following any instructions in this guide or in other materials.

Keep product and batteries away from open flames and extreme heat. Avoid direct sunlight or heat exposure. Always
remove all batteries from products that are being stored and not used. Batteries may damage the appliance if they leak.
Do not use rechargeable batteries. Ensure correct polarity when inserting the batteries. Improper battery use may
damage the product.

Door / Window Sensor 7 is intended for indoor use in dry locations only. Do not use in damp, moist, and/or wet
locations.
It contains small parts; keep away from children.

 

 

Quick Start

Pre-Installation of Door / Window Sensor 7.

Summary of Contents for AEO ZWA008-C











Reviews: