Model number: ZW130.
Power supply: Rechargeable lithium battery, 3.7 V, 640mAh.
Battery charger input: Micro USB port, DC 5V±0.5V, max 1A.
Operating temperature: 0°C to 40°C.
Technical Specifications
Warranty.
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR
TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS
TO THIS EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE
USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY
LOCATIONS. DO NOT IMMERSE IN WATER. NOT FOR USE WHERE
DIRECTLY EXPOSED TO WATER.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including
interference that may cause undesired operation. This equipment
has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
1
2
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consul the dealer or an experienced radio/TV technician for help.
Do not dispose of electrical appliances as unsorted municipal waste,
use separate collection facilities.
Contact your local government for information regarding the collection
systems available.
Warning
Certifications (regional):
Version: 501011900002-AA www.aeotec.com
Z-Wave and Z-Wave Plus are
registered trademarks of Sigma
Designs and its subsidiaries in the
United States and other countries
FCC ID: XBAFT130
Your WallMote Quad has a internal rechargeable lithium battery that
will allow you to charge it when it is in low battery. The charger’s
output should be a micro USB terminal with the specification of
output DC 5V/1A. When the WallMote Quad is in charge state, the
orange LED will be on. If the orange LED is off and the green LED
remains on, then it indicates that the battery charge is complete.
Note: When the WallMote is in low battery, you will see the orange
LED will blink when you touch the control buttons. Otherwise, if the
blue LED blinks when touching the buttons, which means the battery
is in normal level.
The WallMote Quad also supports sliding control, when the parameter
4 is set to 3, you can slide up or down on the button area to control
the dimmer device.
If at some stage, your primary controller is missing or inoperable, you
may wish to reset all of your WallMote Quad’s settings to their factory
defaults. To do this, follow the steps below:
If you are in need of any technical support during or subsequent to
your products’ warranty, please get in touch with our support team via
http://aeotec.com/support. The Company you bought this product
from has also guaranteed to assist you with any of your support
needs, and you can also contact them for accordingly.
This guarantee made by the company who you purchased the
product from includes the transfer of Aeon Labs’ full warranty to that
Company. They’ve guaranteed that they’ll be able to assist you, the
Customer, with all technical support and repair needs on our behalf.
Aeon Labs warrants to the original purchaser of Products, that is
the Company who you have purchased from, that for the Warranty
Period (as defined below), the Products will be free from material
defects in materials and workmanship. The foregoing warranty is
subject to the proper installation, operation and maintenance of the
Products in accordance with installation instructions and the operating
manual supplied. Warranty claims must be made to the Company
who you have purchased from in writing within thirty (30) days of the
manifestation of a problem.
Aeon Labs' sole obligation under the foregoing warranty is, at Aeon
Labs' option, to repair, replace or correct any such defect that was
present at the time of delivery, or to remove the Products and to
refund the purchase price to Company.
The Warranty Period begins on the date the Products is delivered
and continues for 12 months. Any repairs under this warranty must
be conducted by an authorized Aeon Labs service representative
and under Aeon Labs' RMA policy. Any repairs conducted by
unauthorized persons shall void this warranty.
Excluded from the warranty are problems due to accidents, acts of
God, civil or military authority, civil disturbance, war, strikes, fires, other
catastrophes, misuse, misapplication, storage damage, negligence,
electrical power problems, or modification to the Products or its
components.
Aeon Labs does not authorize any person or party to assume
or create for it any other obligation or liability in connection with
the Products except as set forth herein. Aeon Labs will pass on
to Company all manufacturers’ Material warranties to the extent
that they are transferable, but will not independently warrant any
Material. Company will assist Customer with all warranty, repair,
return and technical support needs, Company must prepay shipping
and transportation charges for returned Products, and insure the
shipment or accept the risk of loss or damage during such shipment
and transportation. Aeon Labs will ship the repaired or replacement
products to Company freight prepaid.Customer and Company shall
indemnify, defend, and hold Aeon Labs and Aeon Labs' affiliates,
shareholders, directors, officers, employees, contractors, agents and
other representatives harmless from all demands, claims, actions,
causes of action, proceedings, suits, assessments, losses, damages,
liabilities, settlements, judgments, fines, penalties, interest, costs and
expenses (including fees and disbursements of counsel) of every kind
(i) based upon personal injury or death or injury to property to the
extent any of the foregoing is proximately caused either by a defective
product (including strict liability in tort) or by the negligent or willful acts
or omissions of Customer or its officers, employees, subcontractors
or agents, and/or (ii) arising from or relating to any actual or alleged
infringement or misappropriation of any patent, trademark, mask
work, copyright, trade secret or any actual or alleged violation of any
other intellectual property rights arising from or in connection with the
products, except to the extent that such infringement exists as a result
of Aeon Labs' manufacturing processes.
IN NO EVENT SHALL AEON LABS BE LIABLE FOR ANY INDIRECT,
INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL
DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE,
OR USE INCURRED BYCUSTOMER, COMPANY OR ANY THIRD
PARTY, WHETHER IN AN ACTION IN CONTRACT, OR TORT,
OR OTHERWISE EVENIF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. AEON LABS' LIABILITY AND CUSTOMER'S
EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION ARISING IN
CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF
THE PRODUCTS, WHETHER BASED ON NEGLIGENCE, STRICT
LIABILITY, BREACH OF WARRANTY, BREACH OF AGREEMENT,
OR EQUITABLE PRINCIPLES, IS EXPRESSLY LIMITED TO, AT
AEON LABS' OPTION, REPLACEMENT OF, OR REPAYMENT OF
THE PURCHASE PRICE FOR THAT PORTION OF PRODUCTS
WITHRESPECT TO WHICH DAMAGES ARE CLAIMED. ALL
CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS
AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL BE
DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY
(30) DAYS FROM AEON LABS' DELIVERY, OR THE DATE FIXED
FOR DELIVERY IN THE EVENT OF NONDELIVERY. THE INDEMNITY
AND WARRANTY IN ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL
OTHER INDEMNITIES OR WARRANTIES, WHETHER EXPRESS
OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
7
6
FCC NOTICE (for USA)
2
Button 1 Basic Set
On/Off control via Button 1
3
Button 1 Multilevel
Switch Set
Dimmer control via Button
1
4
Button 2 Basic Set
On/Off control via Button 2
5
Button 2 Multilevel
Switch Set
Dimmer control via Button
2
6
Button 3 Basic Set
On/Off control via Button 3
7
Button 3 Multilevel
Switch Set
Dimmer control via Button
3
8
Button 4 Basic Set
On/Off control via Button 4
9
Button 4 Multilevel
Switch Set
Dimmer control via Button
4
Dimmer control via sliding the button area.
Your WallMote Quad’s battery.
Resetting your WallMote Quad.
Slide direction
1.
2.
3.
Press and hold the Action button (20 seconds).
The LED should blink between green, purple, then red which will
flash rapidly until a green LED becomes solid for 2 seconds to
indicate a successful factory reset.
Let go of the Action Button.
Association table of the control buttons.
The WallMote Quad supports 9 association groups, all control buttons
can activate the configured scenes via sending the Central Scene
Notifications to primary controller/gateway (In association group 1).
Every control button also can send the control commands to control
the devices in the other association groups, see the table below:
Note: You can also enable or disable the sound effects via pressing
and holding the Action Button for 12 seconds (the buzzer chirp once
and the red LED will fast blink) and then release.
Touch vibration
This will enable or disable the vibration effects when you press or
touch the sensing area. By default, this is enabled.
Parameter 2 [1 byte]
0: Disable
1: Enable
Note: You can also enable or disable the vibration effects via pressing
and holding the Action Button for 17 seconds (the buzzer chirp once
and the red LED will be solid) and then release.
Association
Group
Control
Button
Control
commands
Description
1
(Lifeline)
Button 1
to 4
Central Scene
Notification
Central Scene control via
Button 1 to 4
Relative humidity: 8% to 80%.
Operating distance: Up to 394 feet/120 metres outdoors.
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
