ELECTRICAL SPECIFICATIONS
Nominal Range:
200A
Measurement Range:
0.1 to 240A
Transformation Ratio:
Voltage output
Output Signal:
10mV/A
Accuracy and Phase Shift*:
Accuracy: 0.5 to 10A: 3.0% Reading ± 5mV
10 to 40A: 2.5% Reading ± 5mV
40 to 100A: 2.0% Reading ± 5mV
100 to 240A: 1.0% Reading ± 5mV
Phase Shift: 0.5 to 10A:
Not Specified
10 to 40A:
5°
40 to 100A:
3°
100 to 240A:
2.5°
(*Reference conditions: 18° to 28°C, 20 to 75% RH,
external magnetic field <40 A/m, 48 to 65 Hz sine wave,
distortion factor less than 1%, no DC component, no
external current carrying conductor, test sample
centered.) Load impedance > 1M
.
Overload:
240A for 10 min ON, 30 min OFF
Frequency Range:
40 to 10kHz
Limit Operating Conditions:
200A permanently to 1 kHz
Derating above 3 kHz: 200A x (1/0.333 F), F in kHz
Crest Factor:
3 @ 200Arms with an error (due to CF) of 3%
Working Voltage:
600Vrms
Common Mode Voltage:
600Vrms
Influence of Adjacent Conductor:
< 15mA/A at 50 Hz
Influence of DC on AC signal:
DC Current < 20A, < 5%
Influence of Conductor Position in Jaw:
0.5% of mV output @ 50/60Hz
Influence of Frequency:
40 Hz to 1 kHz: 3% of mV output
1 kHz to 10 kHz: 12% of mV output
Influence of Load:
< 3% of mA output from 40Hz to 1kHz
< 12% of mA output from 1kHz to 10kHz
Influence of Temperature:
150 ppm/°K, or 0.15% of mV output per 10°K
Influence of Humidity (10 - 90% RH):
0.2% of mV output per 10°K @ 18°C to 28°C
MECHANICAL SPECIFICATIONS
Operating Temperature:
14° to 131°F (-10° to +55°C)
Storage Temperature:
-40° to 158°F (-40° to +70°C)
Operating Relative Humidity:
10° to 35°C 85% RH (without roll-off above 35°C)
Maximum Cable Diameter:
One Ø 0.78" (20mm), bus bar 20 x 5mm
Case Protection:
IP 40 (IEC 529)
Drop Test:
Test per IEC 68-2-32: 1.0m drop on 38mm of
Oak on concrete.
Mechanical Shock:
Test per IEC 68-2-27
Vibration:
Test per IEC 68-2-6
Dimensions:
5.47 x 2.00 x 1.18" (139 x 51 x 30mm)
Weight:
6.5 oz (180g)
Polycarbonate Material:
Jaws: Polycarbonate with 10% fiberglass charge,
Red UL 94 V0
Case: Polycarbonate 920A Gray
Opening Operations - Life:
> 50,000
Output:
MN252:
Two standard safety banana jacks (4mm)
MN253:
Double/reinforced insulated 5 ft (1.5m)
lead with safety 4mm banana plug
SAFETY SPECIFICATIONS
Electrical:
Double insulation or reinforced insulation between
the primary or secondary and the outer case of the
handle conforms to IEC 1010-2-32.
Common Mode Voltage:
600V CAT III, Pollution Degree 2
Dielectric Strength:
5550V, 50/60 Hz between primary, secondary
and the outer case of the handle
Electromagnetic Compatibility:
EN 50081-1 Class B
EN 50082-2 Electrostatic discharge
IEC 1000-4-2
Radiated field IEC 1000-4-3
Fast transients IEC 1000-4-4
Magnetic field at 50/60 Hz IEC 1000-4-8
ORDERING INFORMATION
AC Current Probe MN252
.................
Cat #2115.78
AC Current Probe MN253
.................
Cat #2115.79
Accessories:
Leads, set of 2, 5 ft safety
(1000V) for Model MN252 ...................
Cat #2111.29
Banana plug adapter
(to non-recessed plug) .......................
Cat #1017.45
E192383
2.56"
(65 mm)
5.47"
(139 mm)
.83"
(21 mm)
Black
Red
.73"
2.00"
(51 mm)
(18.5 mm)
.1.18"
(30 mm)
Tactical
Barrier
(keep hands below
this barrier)
MN252 MN253
www
.
ShopAEMC
.ca
Shop for
AEMC products online at:
1.800.561.8187
