background image

10

AEM Air Intake System Warranty Policy

AEM

®

 warrants that its intake systems will last for the life of your vehicle. AEM will not honor this warranty due to mechani-

cal damage (i.e. improper installation or fitment), damage from misuse, accidents or flying debris. AEM will not warrant 
its powder coating if the finish has been cleaned with a hydrocarbon-based solvent. The powder coating should only be 
cleaned with a mild soap and water solution. Proof of purchase of both the vehicle and AEM intake system is required for 
redemption of a warranty claim.  

This warranty is limited to the repair or replacement of the AEM part. In no event shall this warranty exceed the original 
purchase price of the AEM part nor shall AEM be responsible for special, incidental or consequential damages or cost 
incurred due to the failure of this product. Warranty claims to AEM must be transportation prepaid and accompanied with 
dated proof of purchase. This warranty applies only to the original purchaser of product and is nontransferable.  Improper 
use or installation, use for racing, accident, abuse, unauthorized repairs or alterations voids this warranty.  AEM disclaims 
any liability for consequential damages due to breach of any written or implied warranty on all products manufactured by 
AEM. Warranty returns will only be accepted by AEM when accompanied by a valid Return Merchandise Authorization 
(RMA) number. Credit for defective products will be issued pending inspection. Product must be received by AEM within 
30 days of the date RMA is issued.  

If you have a warranty issue, please call (800) 992-3000 and our customer service department will assist you. A proof of 
purchase is required for all AEM warranty claims.

10-290

09/28/11

Summary of Contents for 21-705











Reviews: