AEM Performance Electronics 30-3300 Instruction Manual Download Page 10

Page: 10 / 21

Water/Methanol Injection V2

Pump/Tank Flush

After all wires are hooked up, add water to the tank and, with the hose pointed into a container, press and hold
the TEST push button on the controller module. The TEST button can be used to test the system. The pump
speed will gradually increase from zero to full speed within 3 seconds and then remain full for another 3
seconds before stopping. Repeat the TEST button procedure until you are sure the system is free of any debris
that may have been in the lines or tank. Drain the water out of the tank and refer to the next section on installing
the nozzle.

Nozzle Selection

This injection kit includes three differently sized atomizing pintles that cover a very large range of horsepower
levels. Use the following chart to select the appropriate pintle for your power level. The kit comes with the 500cc
pintle already preassembled.

Fuel Flow

N/A

(.5 BSFC)

Fuel Flow

F/I

(.7 BSFC)

W/M Flow

N/A

W/M Flow

–

10psi

Boost

W/M Flow

–

25psi

Boost

W/M Flow

25+psi

Boost

150

788

1101

220

275

330

200

1050

1469

126

294

367

441

250

1313

1836

158

367

459

551

300

1575

2203

189

441

551

661

350

1838

2570

221

514

642

771

Nozzle

400

2100

2937

252

587

734

881

250

450

2363

3304

284

661

826

991

500

2625

3671

315

734

918

1101

1000

550

2888

4038

347

808

1010

1212

1000 + 500

600

3150

4406

378

881

1101

1322

1000 + 1000

650

3413

4773

410

955

1193

1432

700

3675

5140

441

1028

1285

1542

750

3938

5507

473

1101

1377

1652

800

4200

5874

504

1175

1469

1762

850

4463

6241

536

1248

1560

1872

900

4725

6608

567

1322

1652

1983

950

4988

6976

599

1395

1744

2093

1000

5250

7343

630

1469

1836

2203

Summary of Contents for 30-3300






















Search results

Summary of Contents for 30-3300

Reviews:

Brands by name

Popular brands

AEM Performance Electronics 30-3300, Instruction Manual

Search results

Summary of Contents for 30-3300

Reviews:

Brands by name

Popular brands