AEG VA6011LT User Instructions Download Page 38 | Manualshive

Page: 38 / 48

AEG VA6011LT User Instructions Download Page 38

Installation and Connection Instructions

38

INSTALLATION AND CONNECTION
INSTRUCTIONS

Installing the Dishwasher

• The dishwasher must be installed on a firm floor and adjusted to

ensure that it is stable and level.

• To compensate for unevenness in the

floor and to match the height of the
appliance to that of surrounding units
extend the threaded feet by unscrew-
ing:
– use a screwdriver.

• For built-in, integrated and fully inte-

grated dishwashers, the rear feet
should be adjusted from the front of
the appliance using a screwdriver.

• The drain hose, inlet hose and mains

cable must not be kinked or crushed
when the dishwasher is in position.

• In addition, the dishwasher must be firmly screwed to the work sur-

face or to the neighbouring units. This is essential to ensure the dish-
washer does not tip.

Installing the Furniture Door

(see installation stencil supplied)

3

The door of the appliance can be fitted with a wooden furniture door
of the following dimensions:

Width:

591 mm – 594 mm

Thickness:

16 mm – 24 mm

Height:

max. 715 mm

Weight:

max. 10 kg

«
...
36
37
38
39
40
...
»

Summary of Contents for VA6011LT

















































Reviews:

No comments