AEG VA6011LT User Instructions Download Page 16 | Manualshive

Page: 16 / 48

AEG VA6011LT User Instructions Download Page 16

Operating Instructions

16

3.

Press function button

2

.

The LED indicator for function button

2

will flash.

The

L

indicator will indicate the current setting:

4.

Pressing function button

2

activates and deactivates the rinse aid dis-

pensing function.

5.

If the rinse aid dispensing function has been correctly set, press the
ON/OFF switch.
The setting of the rinse aid dispensing function is now saved.

Adding rinse aid

If you are using dishwasher detergent and rinse aid separately, add the
rinse aid:
– Before using the dishwasher for the first time.
– When the

H

indicator on the control panel is illuminated.

The rinse aid compartment is on the inside of the dishwasher door.

0

1.

Open the door.

2.

Press the rinse aid compartment
release button with your finger.

3.

Fully open the rinse aid compartment
lid.

The

L

indicator will

become illuminated:

Rinse aid inflow activated
(ex-factory setting)

The

L

indicator is not illu-

minated:

Inflow of rinse aid is deactivated

«
...
14
15
16
17
18
...
»

Summary of Contents for VA6011LT

















































Reviews:

No comments