background image

• At first installation or after reversing

the door wait at least 4 hours before

connecting the appliance to the power

supply. This is to allow the oil to flow

back in the compressor.

• Before carrying out any operations on

the appliance (e.g. reversing the

door), remove the plug from the

power socket.

• Do not install the appliance close to

radiators or cookers, ovens or hobs.

• Do not expose the appliance to the

rain.

• Do not install the appliance where

there is direct sunlight.

• Do not install this appliance in areas

that are too humid or too cold.

• When you move the appliance, lift it

by the front edge to avoid scratching

the floor.

2.2 Electrical connection

WARNING!

Risk of fire and electric

shock.

WARNING!

When positioning the

appliance, ensure the supply

cord is not trapped or

damaged.

WARNING!

Do not use multi-plug

adapters and extension

cables.

• The appliance must be earthed.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Always use a correctly installed

shockproof socket.

• Make sure not to cause damage to

the electrical components (e.g. mains

plug, mains cable, compressor).

Contact the Authorised Service

Centre or an electrician to change the

electrical components.

• The mains cable must stay below the

level of the mains plug.

• Connect the mains plug to the mains

socket only at the end of the

installation. Make sure that there is

access to the mains plug after the

installation.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

2.3 Use

WARNING!

Risk of injury, burns, electric

shock or fire.

 The appliance contains flammable

gas, isobutane (R600a), a natural gas

with a high level of environmental

compatibility. Be careful not to cause

damage to the refrigerant circuit

containing isobutane.
• Do not change the specification of this

appliance.

• Any use of the built-in product as free-

standing is strictly prohibited.

• Do not put electrical appliances (e.g.

ice cream makers) in the appliance

unless they are stated applicable by

the manufacturer.

• If damage occurs to the refrigerant

circuit, make sure that there are no

flames and sources of ignition in the

room. Ventilate the room.

• Do not let hot items to touch the

plastic parts of the appliance.

• Do not store flammable gas and liquid

in the appliance.

• Do not put flammable products or

items that are wet with flammable

products in, near or on the appliance.

• Do not touch the compressor or the

condenser. They are hot.

2.4 Internal lighting

WARNING!

Risk of electric shock.

• This product contains a light source of

energy efficiency class G.

• Concerning the lamp(s) inside this

product and spare part lamps sold

separately: These lamps are intended

to withstand extreme physical

conditions in household appliances,

such as temperature, vibration,

humidity, or are intended to signal

information about the operational

ENGLISH

5

Summary of Contents for SKK582F1AF

















Reviews: