background image

2. Open the appliance door. If

necessary, add or remove the items.

3. Close the door and touch the Start/

Pause button.

The programme or the delay start

continues.

4. The door can be opened when the

programme is complete. You may

also set a spinning or draining

programme/option and than press

Start/Pause button. If the spin and

drain programmes are not available

in the programme dial, they can be

set via App.

11.12 End of the programme

When the programme has finished, the

appliance stops automatically. The

acoustic signals operate (if they are

active).
In the display all washing phase

indicators become steady and the time
area shows  .
The indicator of the Start/Pause button

goes off.

The door unlocks and the indicator 

goes off.

1. Press the On/Off button to deactivate

the appliance.

After five minutes from the end of the

programme, the energy saving function

automatically deactivates the appliance.

When you activate the

appliance again, the display

show the end of the last

selected programme. Turn

the programme dial to set a

new cycle.

2. Remove the laundry from the

appliance.

3. Make sure that the drum is empty.

4. Keep the door and the detergent

dispenser slightly ajar to prevent

mildew and odours.

5. Close the water tap.

11.13 Draining water out after

end of cycle

If you have chosen a programme or an

option that does not empty out the water

of the last rinse, the programme is

completed, but:

• The display shows the indicator  , the

option indicator 

 or   and the

door locked indicator 

. The

indicator of the running phase 

flashes.

• The drum still turns at regular

intervals to prevent the creases in the

laundry.

• The door stays locked.

• You must drain the water to open the

door:

1. If necessary, touch the Spin button to

decrease the spin speed proposed

by the appliance.

2. Touch the Start/Pause button:

• If you have set 

, the appliance

drains the water and spins.

• If you have set  , the appliance

only drains the water.

The option indicator 

 or   goes off,

while the indicator   flashes and then

goes off.

3. When the programme is completed

and the door locked indicator 

goes off, you can open the door.

4. Press the On/Off button a few

seconds to deactivate the appliance.

In any case, the appliance

empties the water out

automatically after

approximately 18 hours.

11.14 Stand-by option

The Stand-by function automatically

deactivates the appliance to decrease

the energy consumption when:
• You do not use the appliance for 5

minutes before you touch the Start/

Pause button.

Press the On/Off button to activate

the appliance again.

• After 5 minutes from the end of the

washing programme

Press the On/Off button to activate

the appliance again.

The display shows the end of the last

set programme.

ENGLISH

39

Summary of Contents for L8FEC966CA





























































Reviews: