background image

17.8 Cleaning the detergent

dispenser

To prevent possible deposits of dried

detergent or clotted fabric softener

and/or formation of mould in the

detergent dispenser drawer, once in a

while carry out the following cleaning

procedure:

1. Open the drawer. Press the catch

downwards as indicated in the

picture and pull it out.

1

2

2. Remove the top part of the additive

compartment to aid cleaning. Make

sure that all detergent residue is

removed from the upper and lower

part of the recess. Use a small brush

to clean the recess.

3. Flush the detergent drawer out under

running warm water to remove any

traces of accumulated detergent.

After cleaning, replace the top part in

its position.

4. Insert the detergent drawer into the

guide rails and close it. Run the

rinsing programme without any

clothes in the drum.

17.9 Cleaning the drain pump

WARNING!

Disconnect the mains plug

from the mains socket.

Regularly check the drain

pump filter and make sure

that it is clean.

Clean the drain pump if:

• The appliance does not drain the

water.

• The drum does not turn.

• The appliance makes an unusual

noise because of the blockage of the

drain pump.

• The display shows the alarm code

.

WARNING!

• Do not remove the filter

while the appliance

operates.

• Do not clean the pump if

the water in the appliance

is hot. Wait until the water

cools down

Proceed as follows to clean the pump:

1. Open the pump cover.

www.aeg.com

40

Summary of Contents for L7WEE862S





















































Reviews: