background image

Once removed the exceeding garments,

touch the Départ/Pause button to start

the programme again. The ProSense

phase can be repeated up to three times

(see point 1).
Important! If the laundry amount will not

be reduced, the washing programme

starts anyway, despite the overload. In

this case, it will be not possible to

guarantee the best washing results.

About 20 minutes after the

programme start, the

programme duration could

be adjusted again depending

on the capacity of water

absorption of the fabrics.

The ProSense detection is

carried out with complete

washing programmes only

(no skipping phase

selected).

The ProSense is not

available with some

programmes, such as Laine/

Soie, programmes with short

cycles and without washing

phase.

11.13 Opening the Lid when

the programme operates

CAUTION!

If the temperature and level

of the water in the drum are
too high, the 

 indicator

stays on and you cannot

open the lid.

To open the lid proceed as follows:

1. Press the button Marche/Arrêt for

some seconds to deactivate the

appliance.

2. Wait for some minutes and then open

carefully the lid.

3. Close the lid.

4. Activate the appliance and set the

programme again.

11.14 Opening the Lid when

the delay start is active

While the delay start operates, the

appliance lid is locked.
To open the appliance lid:

1. Press button Départ/Pause.

The 

 indicator goes off.

2. Open the appliance lid.

3. Close the lid and press button

Départ/Pause.

The delay start continues.

11.15 End of cycle

When the programme has finished, the

appliance stops automatically. The

acoustic signal operates (if it is active).

In the display   comes on and the lid
locked indicator 

 goes off.

The indicator of Départ/Pause button

goes off.

1. Press button Marche/Arrêt to

deactivate the appliance.

After five minutes from the end of the

programme, the energy saving function

automatically deactivates the appliance.

When you activate the

appliance again, the display

show the end of the last set

programme. Turn the

programme knob to set a

new cycle.

2. Remove the laundry from the

appliance.

3. Make sure that the drum is empty.

4. Keep the door ajar, to prevent mildew

and odours

11.16 Draining water out after

end of cycle

The washing programme is

completed, but there is water in the

drum:
The drum turns regularly to prevent the

creases in the laundry.

The lid lock indicator 

 is on. The lid

stays locked.
You must drain the water to open the lid:

www.aeg.com

24

Summary of Contents for L7TDR722E









































Reviews: