background image

Problem and alarm code

Possible cause and solution

The level of water inside the

appliance is too high.

The display shows iF1.

• Switch the appliance off and on.

• Make sure that the filters are clean.

• Make sure that the outlet hose is installed at the right

height above the floor. Refer to the installation instruc‐

tions.

The appliance stops and

starts more times during op‐

eration.

• It is normal. It provides optimal cleaning results and en‐

ergy savings.

The programme lasts too

long.

• If the delay start option is set, cancel the delay setting or

wait for the end of the countdown.

• Activating options can increase the programme duration.

The displayed programme

duration is different than the

duration in the consumption

values table.

• Refer to the consumption values table in the chapter 

"Programmes".

The remaining time in the

display increases and skips

nearly to the end of the pro‐

gramme duration.

• This is not a defect. The appliance is working correctly.

Small leak from the appli‐

ance door.

• The appliance is not levelled. Loosen or tighten the ad‐

justable feet (if applicable).

• The appliance door is not centred on the tub. Adjust the

rear foot (if applicable).

The appliance door is diffi‐

cult to close.

• The appliance is not levelled. Loosen or tighten the ad‐

justable feet (if applicable).

• Parts of the tableware are protruding from the baskets.

The appliance door opens

during the wash cycle.

• The AirDry function is activated. You can deactivate the

function. Refer to "Settings".

Rattling or knocking sounds

from the inside of the appli‐

ance.

• The tableware is not properly arranged in the baskets.

Refer to basket loading leaflet.

• Make sure that the spray arms can rotate freely.

The appliance trips the cir‐

cuit-beaker.

• The amperage is insufficient to supply simultaneously all

the appliances in use. Check the socket amperage and

the capacity of the meter or turn off one of the applian‐

ces in use.

• Internal electrical fault of the appliance. Contact an Au‐

thorised Service Centre.

The appliance is switched

on but does not operate.

The display shows PF.

• Power supply is out of the operating range. The wash

cycle is temporarily interrupted and resumes automati‐

cally once the power is restored.

The appliance switches off

during operation.

• Complete power outage. The wash cycle is temporarily

interrupted and resumes automatically once the power

is restored.

www.aeg.com

24

Summary of Contents for FEE84706PM





























Reviews: