AEG FAVORIT 65050 VI User Instructions Download Page 9 | Manualshive

Page: 9 / 48

AEG FAVORIT 65050 VI User Instructions Download Page 9

Operating Instructions

9

Display and control panel

Function buttons:

In addition to the programme and/or start delay

selected, the following functions can also be set with the help of these
buttons:

The multi-display

can indicate:

– the start delay that has been set.
– the estimated time remaining for the current programme.
– what type of error has occurred with the dishwasher.
– the level of hardness to which the water softener is set.
– whether the rinse aid inflow has been activated/deactivated.
– whether the acoustic signal has been activated/deactivated.

The indicators

have the following meanings:

3

The indicators are never illuminated while a programme is running.

Function button

1

Set water softener

Function button

2

Activate/deactivate rinse aid inflow

Function button

3

Activate/deactivate acoustic signal

Function button

4

- not programmed -

J

Refill special salt

H

Refill rinse aid

^

Open the tap

Multi-display

Function buttons

1

2

3

4

Set start delay

Indicators

ON/OFF button

«
...
7
8
9
10
11
...
»

Summary of Contents for FAVORIT 65050 VI

















































Reviews:

No comments