AEG FAVORIT 40650 User Information Download Page 33

33

Water drainage

Drain hose

1

The drain hose must not be kinked, crushed or entangled.
Connecting the drain hose:

Maximum permitted height: 1 metre.

Minimum required height: 40 cm above the bottom edge of the ap-
pliance.

Extension hoses

Extension hoses are available from 
your local Service Force Centre. To 
ensure that the function of the ap-
pliance is not impeded, the internal 
diameter of extension hoses must 
be 19 mm.

 

Extension hoses must not be laid 
more than a maximum distance of 
3 metres horizontally; the maxi-
mum permitted height for the con-
nection for the drain hose is then 
85 cm.

Sink outlet connection

The outlet of the drain hose (ø 19 mm) fits all commonly available 
sink outlet types. The outer diameter of the sink outlet connection 
must be at least 15 mm.

The drain hose must be fixed to the sink outlet connection using the 
hose clamp supplied.

Water drainage if the dishwasher is built-in at high level

If the dishwasher is installed at a high level, and the drain hose connec-
tion is less than 30 cm from the lower edge of the appliance, adapter 
kit ET 111099520 must be fitted by your local Service Force Centre.

Summary of Contents for FAVORIT 40650









































Reviews: