20
BSS18SBL
BSS18S12BL
...................... 4772 54 01... ..................4772 61 01
...000001-999999
...000001-999999
.......................... 1/4" (6,35 mm) ............... 1/2" (12,7 mm)
..................... 0-2900 min
-1
................... 0-2800 min
-1
..................... 0-4200 min
-1
................... 0-3800 min
-1
...........................200 Nm .......................... 280 Nm
..........................M14 ............................... M18
.............................18 V ............................... 18 V
..................1,3 ... 2,0 kg ................... 1,4 ... 2,1 kg
........................................... -18...+50 °C
......................................L1815R, ... L1890R
....................... AL18G, AL1218G, BL1218, BLK1218
..........................96,0 dB (A) ..................... 96,0 dB (A)
........................107,0 dB (A) ................... 107,0 dB (A)
..........................13,0 m/s
2
........................... 13 m/s
2
............................1,5 m/s
2
.......................... 1,5 m/s
2
ENGLISH
TECHNICAL DATA CORDLESS IMPACT DRIVER / WRENCH
Production code...........................................................................
Tool reception ..............................................................................
No-load speed .............................................................................
Impact rate (high speed)..............................................................
Max. torque with battery 6.0 Ah ...................................................
Max. diameter bolt / nut ...............................................................
Battery voltage.............................................................................
Weight according EPTA-Procedure 01/2014 (1.5 Ah ... 9.0 Ah) ........
Recommended ambient operating temperature ..........................
Recommended battery types.......................................................
Recommended charger ...............................................................
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) .........................
Sound power level (Uncertainty K=3dB(A)) ..............................
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined
according to EN 62841.
Vibration emission value a
h
Impact tightening of fasteners of the maximum capacity of the tool
Uncertainty K=
..........................................................................
WARNING Read all safety warnings, instructions,
illustrations and speci
fi
cations provided with this power
tool.
Failure to follow all instructions listed below may result in
electric shock,
fi
re and/or serious injury.
Save all warnings and instructions for future reference.
IMPACT DRIVER / WRENCH SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring.
Fasteners contacting a „live“ wire may make
exposed metal parts of the power tool „live“ and could give the
operator an electric shock.
Wear ear protectors.
Exposure to noise can cause hearing
loss.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection
mask.
Do not machine any materials that present a danger to health
(e.g. asbestos).
Switch the device o
ff
immediately if the insertion tool stalls! Do
not switch the device on again while the insertion tool is stalled,
as doing so could trigger a sudden recoil with a high reactive
force. Determine why the insertion tool stalled and rectify this,
paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING!
Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is
running.
When working in walls ceiling, or
fl
oor, take care to avoid
electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household refuse
or by burning them. AEG Distributors o
ff
er to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System GBS chargers for charging System GBS
battery packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in
dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery
acid wash it o
ff
immediately with soap and water. In case of eye
contact rinse thoroughly for at least 10 minutes and
immediately seek medical attention.
Warning!
To reduce the risk of
fi
re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in
fl
uid or allow a
fl
uid to
fl
ow inside them.
Corrosive or conductive
fl
uids, such as seawater, certain
industrial chemicals, and bleach or bleach containing products,
etc., can cause a short circuit.
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test
given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for di
ff
erent
applications, with di
ff
erent accessories or poorly maintained, the vibration and noise emission may di
ff
er. This may signi
fi
cantly
increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched o
ff
or
when it is running but not actually doing the job. This may signi
fi
cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the e
ff
ects of vibration and/or noise such as: maintain the tool and
the accessories, keep the hands warm, organization of work patterns.
470 410 - BSS18SBL, BSS18S12BL_EN62841.indd 20
470 410 - BSS18SBL, BSS18S12BL_EN62841.indd 20
30.06.2020 12:45:17
30.06.2020 12:45:17
