AE Techron 7224, Operator'S Manual

Page: 5 / 50

List of Figures
Figure 1.1 – 7224 & 7226 Front Panels
............................................................................................... 6
Figure 3.1 – 7224/7226 Back Panel
.................................................................................................... 8
Figure 3.2 – Closeup of the Output Terminal Resistor
......................................................................... 9
Figure 3.3 – Connecting the Load
....................................................................................................... 9
Figure 3.4 – Closeup of SIM card
........................................................................................................ 9
Figure 3.5 – Wiring for Unbalanced or Balanced Input Connector
.................................................... 10
Figure 3.6 – Closeup of AC Mains Outlet
.......................................................................................... 10
Figure 3.7 – Sample of Configurations Setting Label
........................................................................ 10
Figure 4.1 – Power Switch
................................................................................................................. 12
Figure 4.2 – Gain Control
.................................................................................................................. 12
Figure 4.3 – Push Buttons
................................................................................................................. 13
Figure 4.4 – Indicators
....................................................................................................................... 13
Figure 4.5 – Main Status Indicators
................................................................................................... 13
Figure 4.6 – Fault Status Indicators
................................................................................................... 14
Figure 4.7 – Back Panel Controls and Connectors
........................................................................... 15
Figure 5.1 – Access Panel Screw Locations
..................................................................................... 16
Figure 5.2 – Main Board Location Inside Access Panel
.................................................................... 17
Figure 5.3 – Master/Slave Setting
..................................................................................................... 17
Figure 5.4 – Gain Trim Control
.......................................................................................................... 17
Figure 5.5 – Controlled-Voltage/Controlled-Current Mode Setting
.................................................... 18
Figure 5.6 – Compensation Setting
................................................................................................... 18
Figure 5.7 – Run Mode/Stop Mode on Power-Up Setting
................................................................. 19
Figure 5.8 – Standby Mode on Over Load Setting
............................................................................ 19
Figure 5.9 – Accessing the Power Supply Board
.............................................................................. 20
Figure 5.10 – Location of Amplifier High-Voltage Transformer Sockets
............................................ 20
Figure 5.11 – J3 and J7 Plug Locations for High-Current Output
...................................................... 20
Figure 5.12 – J4 and J8 Plug Locations for High-Voltage Output
..................................................... 20
Figure 5.13 – Bi-Level Power Switch Location
.................................................................................. 20
Figure 6.1 – Remote Status and Control Pinouts
.............................................................................. 22
Figure 6.2 – Remote Run/Standby Monitor
....................................................................................... 22
Figure 6.3 – Remote Status and Reset Schematic
........................................................................... 23
Figure 6.4 – Remote Enable/Standby
............................................................................................... 24
Figure 6.5 – Remote Current Monitoring
........................................................................................... 25
Figure 6.6 – Remote Current Monitoring, Alternate Method
.............................................................. 25
Figure 6.7 – Input to Output Comparison, Controlled-Voltage Operation
.......................................... 26
Figure 6.8 – Input to Output Comparison, Controlled-Current Operation
.......................................... 26
Figure 6.9 – Factory-installed Default RC Network
........................................................................... 27
Figure 6.10 – Custom Compensation Location
................................................................................. 29
Figure 6.11 – Compensation Effects on Waveform
........................................................................... 29
Figure 6.12 – Square Wave Showing a Decrease in R is Required
.................................................. 29
Figure 6.13 – Square Wave Showing an Increase in R is Required
................................................. 29
Figure 6.14 – Square Wave Showing a Decrease in C is Required
.................................................. 29
Figure 6.15 – Main Status Indicators for Multi-Amplifier Systems
..................................................... 32
Figure 6.16 – Fault Status Indicators for Multi-Amplifier Systems
..................................................... 33
Figure 7.1 – Board-Level Functional Block Diagram
......................................................................... 38
Figure 9.1 – +Vcc and –Vcc Point Locations
..................................................................................... 40
Figure 9.2 – Fuse F1 Location
........................................................................................................... 41
Figure 9.3 – Interlock I/O Connector
................................................................................................. 41
Figure 10.1 – 7224 Voltage Potential vs. Frequency
......................................................................... 46
Figure 10.2 – 7226 Voltage Potential vs. Frequency
......................................................................... 46
Figure 10.3 – 7224 & 7226 Frequency Response
............................................................................. 46
Figure 10.4 – 7224 Noise vs. Frequency
........................................................................................... 46
Figure 10.5 – 7224 Continuous Power vs. Frequency
...................................................................... 46
Figure 10.6 – 7224 Thermal Performance
......................................................................................... 46
Figure 10.7 – 7224 DC Current Over Timeat 13.5 VDC
.................................................................... 47
Figure 10.8 – 7224 DC Current Over TimeComparison with 4-ohm Load
......................................... 47
Figure 10.9 – 7224 DO 160 Section 18.2 AC Power Processing
...................................................... 47