Advent ADVEXL12A Installation Manual Download

Page: 3 / 24

TABLE OF CONTENTS

ImpOrTANT NOTICES ��2

GENErAL SySTEm CONFIGurATIONS (Ir TrANSmIT ANd rECEIvE mOdES m1 Or m2) ��3

mATErIALS INCLudEd IN ThIS pACkAGE ��4

INSTALLING ThE uNIT IN A vEhICLE ��5

INSTALLING ThE SNAp-ON ShrOud ANd SCrEEN COvEr ��6

INSTALLING ThE TrIm rING ��7

GENErAL vEhICLE INSTALLATION ApprOACh ��8

vEhICLE prEpArATION ��9

CONNECTING ThE dOmE LIGhTS �� 10

INSTALLING ThE mOuNTING BrACkET �� 12

INSTALLING ThE AdvEXL12A vIdEO SySTEm - wIrING dIAGrAm �� 13

INSTALLING ThE AdvEXL12A vIdEO SySTEm - mOuNTING ThE uNIT �� 14

AppENdIX A- rEmOvING ThE TrIm rING, SNAp-ON ShrOud ANd SCrEEN COvEr �� 15

AppENdIX B- INSTALLING ThE OpTIONAL ThICk TrIm rING �� 16

AppENdIX C- INSTALLING ThE OpTIONAL GAmE mOduLE (mvGp1) �� 17
AppENdIX d- INSTALLING ThE OpTIONAL SmArTSTrEAm mOduLE (wm1) �� 18

TrOuBLEShOOTING �� 19
NOTES �� 21

Summary of Contents for ADVEXL12A

























Search results

Summary of Contents for ADVEXL12A

Reviews:

Related manuals for ADVEXL12A

Brands by name

Popular brands

Advent ADVEXL12A, Installation Manual

Search results

Summary of Contents for ADVEXL12A

Reviews:

Related manuals for ADVEXL12A

Brands by name

Popular brands