Advent ADVDLX10A Installation Manual Download Page 16

14

INSTALLING THE ADVDLX10 A VIDEO SYSTEM

1.  Connect the 6 pin harness to the unit and make the connections to 

the vehicle.

2.  Connect the red and black power wires of the Power Harness to 

vehicle’s electrical system by tapping into an accessory hot line and 

a good ground.

3.  If connecting to an external source, connect the 5 Pin AV Input 

Harness (112-4259 Blue Connector) to provide the AV signals input.

4.  If connecting to an external source, connect the if used 5 Pin AV 

Output Harness (112-4260 White Connector) to provide the AV 

signals output.

5.  Verify all system functions before final mounting of the finished 

assembly.

A/V Source Definitions:

• 

DVD - Built in DVD/USB

• 

AV - Signal Harness (P/N 112-4259 Blue Connector) to the 3 RCA 

Jack Pigtail is used for AV input.

• 

AUX - AUX input (P/N 112B3227) 3.5mm jack to RCA Cable

NOTE: 

The antenna has been designed for optimal performance. 

When installing the unit, position the antenna for best reception.

WIRING DIAGRAM

5 Pin AV input Harness 

(P/N 112-4259 Blue Connector)

5 Pin AV output Harness 

(P/N 112-4260 White Connector)

6 Pin Power/Dome Light

Harness (P/N 112-4270)

 

 

Antenna for

Wireless FM Mod.

See Antenna Note

Optional Relay Box

150 Marcus Blvd., Hauppauge, NY 11788

Technical Assistance: 1-800-225-6074

R

MODEL NO. : ADVDLX10 A 

This device complies with FCC Rules P art 15.
Operation is subject to the following two
conditions : (1) This device may not cause
harmful interference and (2) This device must
accept any interference that may be received,
including interference that may cause
undesired operation.

This product is Class 1 Laser Product and
complies with FDA Rules 21 CFR Chapter 1,
Subchapter J. 

Made in China

FCC ID : ATI9R3ODM21012

132-7888

Inspected By: 

Power + Dome Light 6-Pin Harness

VIO/BRN

BLK/RED

LAMP-COMMON

RED/BLK

LAMP-ON

LAMP-AUTO

Signal Name

Color

RED
BLACK

POWER +12v (SW)
POWER GROUND

Connector

CON6

(BLACK)

AV  Input 5-Pin Harness

VIDEO-IN

YELLOW

RED

AUDIO R-IN

WHITE

AUDIO L-IN

Signal Name

Color

Connector

CON5

(BLUE)

AV  Output 5-Pin Harness

VIDEO-OUT

YELLOW

RED

AUDIO R-OUT

WHITE

AUDIO L-OUT

Signal Name

Color

Connector

CON2

(WHITE )

VOXX ELECTRONICS CORP.

Patented, refer to www.voxxintl.com/company/patents

Summary of Contents for ADVDLX10A

























Reviews: