manualshive.com logo in svg

Advantech UNO-2174A, User Manual

Share
Download
Advantech UNO-2174A User Manual Download Page 30

UNO-2174A/2178A User Manual

22

Chapter 3  Initial Setup

3.1  Inserting a CompactFlash Card                                         

1.

Remove the power cord.

2.

Unscrew the two screws of CF cover in the front panel.

3.

Plug a CompactFlash card with your OS and application program 
into a CompactFlash card slot on board.

4.

Screw back the CF cover to ensure IP40 protection.

3.2  Chassis Grounding

UNO-2174A/2178A provides good EMI protection and a stable ground-
ing base. There is an easy-to-connect chassis grounding point to use.

Figure 3.1: Chassis Grounding Connection

Please also note that system ground and chassis ground are separated in 
UNO-2174A/2178A

Note: 

The CompactFlash is allocated as "the Second-
ary IDE Master" by default.
User can change it to "Primary IDE Master" by 
BIOS setting. Please enter BIOS and select 
"Integrated Peripherals  > IDE Device Setup > 
IDE Configuration > Enhanced Mode" 

    

Summary of Contents for UNO-2174A













































Reviews:

No comments

Brands by name

Popular brands

Load more brands