Advantech SOM-7567 User Manual Download

Page: 43 / 81

SOM-7567 User Manual

Chapter 3

IOS

3.3.11

CSM Configuration

Figure 3.22 CSM Configuration



CSM Support

This item allows users to enable or disable CSM Support.



GateA20 Active

This item allows users to select the timing to active GateA20.



Option ROM Messages

This item allows user to set display mode for Option ROM.



Boot option filter

This option controls Legacy/UEFI ROMs priority.



Network

This item controls the execution of UEFI and Legacy PXE OpROM.



Storage

This item controls the execution of UEFI and Legacy Storage OpROM.



Video

This item controls the execution of UEFI and Legacy Video OpROM.



Other PCI devices

This item determines OpROM execution policy for devices other than Network,
Storage, or Video.

Summary of Contents for SOM-7567


















































































Search results

Summary of Contents for SOM-7567

Reviews:

Related manuals for SOM-7567

Brands by name

Popular brands

Advantech SOM-7567, User Manual

Search results

Summary of Contents for SOM-7567

Reviews:

Related manuals for SOM-7567

Brands by name

Popular brands