Advantech SOM-5871 User Manual Download Page 83

Page: 83 / 104

SOM-5871 User Manual

Chapter 3

MI BIOS

3.1.6

Save & Exit

Feature

Options

Description

Save Changes and Exit

Yes
No

Exit system setup after saving the changes.

Discard Changes and Exit

Yes
No

Exit system setup without saving any
changes.

Save Changes and Reset

Yes
No

Reset the system after saving the changes.

Discard Changes and Reset

Yes
No

Reset system setup without saving any
changes.

Save Changes

Yes
No

Save Changes done so far to any of the setup
options.

Discard Changes

Yes
No

Discard changes done so far to any of the
setup options.

Restore Defaults

Yes
No

Restore/Load Default values for all the setup
options.

Save as User Defaults

Yes
No

Save the changes done so far as User
Defaults.

Restore User Defaults

Yes
No

Restore the User Defaults to all the setup
options.

Launch EFI Shell from
file system device

Yes
No

Attempts to Launch EFI Shell application
(Shell.efi) from one of the available file sys-
tem devices

Summary of Contents for SOM-5871









































































































Search results

Summary of Contents for SOM-5871

Reviews:

Related manuals for SOM-5871

Brands by name

Popular brands

Advantech SOM-5871, User Manual

Search results

Summary of Contents for SOM-5871

Reviews:

Related manuals for SOM-5871

Brands by name

Popular brands