manualshive.com logo in svg

Advantech PCM-3335, User Manual

Share
Download
Advantech PCM-3335 User Manual Download Page 17

10    PCM-3335 User's Manual

IDE hard drive connections

(HARD CON.)

You can attach two Enhanced Integrated Device Electronics hard
disk drives to the PCM-3335's internal controller. The card comes
with a 40-pin flat cable.

Connecting the hard drive

Wire number 1 on the cable is red or blue, and the other wires are
gray.

1. Connect one end of the cable to the IDE connector. Make sure

that the red (or blue) wire corresponds to pin 1 on the connec-
tor, which is labeled on the board (on the right side).

2. Plug the other end of the cable to the Enhanced IDE hard

drive, with pin 1 on the cable corresponding to pin 1 on the
hard drive. (See your hard drive's documentation for the
location of the connector.)

Unlike floppy drives, you can make the connections with any of
the connectors on the cable. If you install two drives, you will
need to set one as the master and one as the slave. You do this
using jumpers on the drives. If you install just one drive, set it as
the master.

Summary of Contents for PCM-3335




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands