Advantech EKI-7659CPI User Manual Download Page 70 | Manualshive

Page: 70 / 101

background image

EKI-7659CPI_Manual_ed33 60

3.2.3

Protocol

User can set the layer 2 protocol setting via this interface.

VLAN configuration

A Virtual LAN (VLAN) is a  logical network grouping that limits the broadcast domain,  which  would allow
you  to  isolate  network  traffic,  so  only  the  members  of  the  VLAN  will  receive  traffic  from  the  same
members  of  VLAN.  Basically,  creating  a  VLAN  from  a  switch  is  logically  equivalent  of  reconnecting  a
group  of  network  devices  to  another  Layer  2  switch.  However,  all  the  network  devices  are  still  plugged
into the same switch physically.

The industrial switch supports port-based and 802.1Q (tagged-based) VLAN. The default configuration of
VLAN operation mode is “Disable”.

Figure 3.30: VLAN Configuration

VLAN configuration - Port-based VLAN

Packets can go among only members of the same VLAN group. Note all unselected ports are treated as
belonging to another single VLAN. If the port-based VLAN enabled, the VLAN-tagging is ignored.

In order for an end station to send packets to different VLAN groups, it itself has to be either capable of
tagging packets it sends with VLAN tags or attached to a VLAN-aware bridge that is capable of
classifying and tagging the packet with different VLAN ID based on not only default PVID but also other
information about the packet, such as the protocol.

«
...
68
69
70
71
72
...
»

Summary of Contents for EKI-7659CPI






































































































Reviews:

No comments

Related manuals for EKI-7659CPI

Brand: GAIM Pages: 2

Brand: IBM Pages: 2

Brand: Datavideo Pages: 58

IP-Reach IPR-M1

Brand: Raritan Pages: 4

Brand: l-com Pages: 12

Brand: Eaton Pages: 2

S5560S-EI Series

Brand: H3C Pages: 37

OfficeConnect WX4400

Brand: 3Com Pages: 528

OfficeConnect 5

Brand: 3Com Pages: 2

OfficeConnect 3C1670500C

Brand: 3Com Pages: 18

LMP-1204G-SFP Series

Brand: ANTAIRA Pages: 20

Elinx EIR418-2SFP-T

Brand: B&B Electronics Pages: 25

Brand: CIS Pages: 3

SecureStack C3K-2XFP IOM

Brand: Enterasys Pages: 72

Brand: Woxcon Pages: 42

Brand: Lindy Pages: 38

Brand: Datavideo Pages: 64

Brand: 3onedata Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands