manualshive.com logo in svg

Advantech ADAM-5550KW Series, User Manual

Share
Download
Advantech ADAM-5550KW Series User Manual Download Page 19

Chapter 1 System Overview 

 
 

1-14 ADAM-5550KW Series User’s Manual

 

 
• RS-232 Mode: Asynchronous full duplex, point to point 

Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, RI, GND 

• RS-485 Mode: Half duplex, multi-drop 

 Signal: DATA+, DATA- 

• Connector: DB-9 pin 
• Transmission speed: Up to 115.2 Kbps 
• Max transmission distance: 

RS-232: 50 feet (15.2 m) 
RS-485: 4,000 feet (1220 m) 

 
1.3.6 RS-485 interface (COM2)

 

• Signals: DATA+, DATA- 
• Mode : Half duplex, multi-drop 
• Connector: Screw terminal 
• Transmission speed: Up to 115.2K bps 
• Max transmission distance: 4000 feet (1220 m) 
 

1.3.7 RS-232 port (COM3) 

(Suitable for touch screen) 

• Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, RI, GND 
• Mode: Asynchronous, point to point 
• Connector: DB-9 pin 
• Transmission speed: Up to 115.2K bps 
• Max transmission distance: 50 feet (15.2 m) 
 

1.3.8 RS-232/485 interface (COM4)

 

• RS-232/485 Mode selectable by jumper 
  RS-485 Signal: DATA+, DATA- 
• RS-232 Mode: Asynchronous full duplex, point to point 

Signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, RI, GND 

• RS-485 Mode: Half duplex, multi-drop 

RS-485 Signal: DATA+, DATA- 

• Connector: DB-9 
• Transmission speed: Up to 115.2K bps 
• Max transmission distance: 

RS-232: 50 feet (15.2 m) 
RS-485: 4000 feet (1220 m) 

 
1.3.9 Isolation 

• COM2: 2500 Vrms  
• COM4: 1000 Vrms (RS-485 only) 
 
 
 

Summary of Contents for ADAM-5550KW Series
































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands