Advanced Mxp-536 Manual Download Page 5

 

 

www.advancedco.com 

 

2.2  Basic Configuration 

 

Each card connected to the 485 Communication Line must have its 
own  address.  This  address  should  be  set  so  that  it  matches  the 
corresponding card within the Advanced PC Config Tool design. 

 

Configuration Defaults

Earth  Monitor  Disabled

:  This  is  the  required  condition  if  the 

card is expected to share a ground plane with the parent fire Panel, 
or  any  other  card  which  also  provides  earth  monitoring  capabilities. 
For  example,  if  multiple  Zone  cards  are  located  in  a  remote 
enclosure, that requires earth monitoring; only 1 of the cards should 
be set to monitoring mode. Slide switch to the ON position to enable 
the earth monitor circuit. 

Radial (Class B) operation

. Slide switch to the ON position to 

put card into Loop (Class A) mode.  

Stand  Alone  Mode

.    Slide  PBUS  switch  to  the  ON  position  to 

enable Peripheral Bus Mode. 

 

In  Peripheral  Bus  mode  the  card  address  is  set  using  the  Address 

switches (as depicted above). 

In Stand Alone mode the address switches are used to configure the EOL setting: 

Bit 0 

Bit 1 

EOL Setting 

Off 

Off 

Default EOL (6K8) 

On 

Off 

4K7 

Off 

On 

3K9 

On 

On 

Not Used (defaults to 6K8) 

 

Note: Bits 2 and 3 current have no function when operating in stand alone mode. 

 

 

 

 

Summary of Contents for Mxp-536

















Reviews: